background image

3

 

Mounting Position

Secure space as shown below when mounting 2 or more 
of this controller or mounting other devices side by side.

Up, down, left and right direction: 
100 mm or more 

Front: 50 mm or more 

100 mm 

100 mm 

100 mm 

100 mm 

100 mm 

100 mm 

100 mm 

100 mm 

50 mm 

50 mm 

 

How to Mount (Control Box)

1. Attach the controller to the control box so that the 

wiring can be taken out from the left side. (See the 
illustration below.) (Screws (

fi

 eld supply): 4)

•  Tighten the screw securely.

2. Remove the upper cover. (Cover-

fi

 xing screws: 4)

 

After the connection and setting (pages 4 to back 
cover) are complete, attach the upper cover. 
(Cover-

fi

 xing screws: 4)

Screw (

fi

 eld supply)

Upper cover

Screw (

fi

 eld supply)

Control 

box

Cover-

fi

 xing screw

 

Power Supply Wiring

•  Be sure to use a dedicated line for power source.
•  Be sure to earth this controller.
•  Do not connect the earth wiring to those of gas pipe, water 

pipe, lighting rod, telephone, etc.

 

Type of wiring

• Use a 

fl

 exible wiring of 2 mm

(Recommended).

•  Use the standard power supply wiring for Europe (such as 

H05RN-F or H07RN-F which conform to CENELEC (HAR) 
rating speci

fi

 cations) or use the wiring based on IEC 

standard (60245 IEC57, 60245 IEC66). 

 

Total Wire Length 
30 m or less

 

Inter-Unit Control Wiring

 

Type of wiring

• Use a 

fl

 exible shield wiring of 0.5 to 2 mm

2

.

 

Total Wire Length
1000 m or less

 

Number of connectable units and devices
(Up to total of 100 units and devices can be 
connected.)

Indoor unit

Up to 64 units per link *

Outdoor unit

Up to 30 units per link

Central control 
device

Up to 10 units

*: The number of indoor units includes the Interface Adaptor. 

 

External I/O Wiring

 

Type of wiring

• Use a 

fl

 exible wiring of 0.5 to 2 mm

2

.

Attention

•  When using the controller at a location susceptible to 

noise, use a shield wiring.

 

Total Wire Length
20 m or less

 

LAN Cable

 

Type of wiring

•  Category 5 or above straight cable

 

Total Wire Length
100 m or less

 

Basic Wiring Diagram

U2

U1

N

L

U2

U1

U1 U2

1-1

1-2

U1 U2

U1 U2

1-1

1-2

U1 U2

U1 U2

U1 U2

L

N

Power source

100-240 V ~ 50/60 Hz

Outdoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Outdoor unit

LAN

cable

LINK 1

Power 

suply 

wiring

Inter-unit 
control wiring

• 

No polarity

LINK 2

Mounting

Wiring

CZ-CFUSCC1̲工説̲E.indd   3

CZ-CFUSCC1̲工説̲E.indd   3

2016/02/17   15:50:20

2016/02/17   15:50:20

Содержание CZ-CFUSCC1









Отзывы: