manualshive.com logo in svg

Panasonic CS-W18CKP, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CS-W18CKP Скачать руководство пользователя страница 15

Cooling in operation according to Remote Control setting.

Time Delay Safety Control (3 minutes)

7 minutes Time Save Control

Anti-Freezing Control

  • 

If the temperature of the indoor heat exchanger falls
continuously below 2°C for 4 minutes or more, the
compressor turns off to protect the indoor heat exchanger
from freezing. The fan speed setting remains the same.

  • 

Compressor will restart again when the indoor heat
exchanger temperature rises to 10°C (Recovery).

3 minutes waiting of Time Delay Safety Control is valid for
Cooling Operation.

Compressor Reverse Rotation Protection Control

Anti-Dew Formation Control

8 Operation Details

8.1. Cooling Mode Operation

  • 

When the compressor is stopped by Remote Control, it restarts after 3 minutes when the Remote Control is turned ON.

  • 

When the setting temperature is reached during cooling operation, the compressor stops and it will not start for 3 minutes.

  • 

The compressor will start automatically if it has stopped for 7 minutes even if the room temperature is between the compressor
ON temperature and OFF temperature.

  • 

If the compressor is operating continuously for 5 minutes or longer and the temperature difference between intake air and
indoor heat exchanger is 2.5°C or less for 2 minutes, compressor will stop and restart automatically.
(Time Delay Safety Control is valid)

▲

T = Intake air temperature - Indoor heat exchanger temperature

This is to protect reverse rotation of the compressor when there is a instantaneous power failure.

  • 

Purpose is to prevent dew formation on indoor unit air discharge area.

  • 

When the following conditions occur for 30 minutes continuously, anti-dew formation is controlled by indoor fan speed shift to
low (Changed to Lo

+

):

  − 

Indoor intake air temperature is more than 24°C and less than 30°C.

  − 

Remote Control setting temperature is less than 25°C.

  − 

Compressor is on.

  − 

Cooling operation mode.

  − 

Indoor Fan motor operate at Low fan speed.

  • 

This control is cancelled immediately when above condition is changed.

15

CS-W18CKP CU-W18CKP5 / CS-W24CKP CU-W24CKP5

Содержание CS-W18CKP














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды