Panasonic CS-V12DKE Скачать руководство пользователя страница 37

Страница: 37 / 80

Attached accessories

Applicable piping kit

CZ-3F5, 7BP (V7DK, V9DK, W7DK, W9DK)

CZ-4F5, 7, 10BP (V12DK, W12DK)

Select the best location

INDOOR UNIT

•

There should not be any heat source or steam near
the unit.

•

There should not be any obstacles blocking the air
circulation.

•

A place where air circulation in the room is good.

•

A place where drainage can be easily done.

•

A place where noise prevention is taken into
consideration.

•

Do not install the unit near the door way.

•

Ensure the spaces indicated by arrows from the wall,
ceiling, fence or other obstacles.

•

Recommended installation height for indoor unit
shall be at least 2.3 m.

OUTDOOR UNIT

•

If an awning is built over the unit to prevent direct
sunlight or rain, be careful that heat radiation from
the condenser is not obstructed.

•

There should not be any animal or plant which could
be affected by hot air discharged.

•

Keep the spaces indicated by arrows from wall,
ceiling, fence or other obstacles.

•

Do not place any obstacles which may cause a short
circuit of the discharged air.

•

If piping length is over the rated length, additional
refrigerant should be added as shown in the table.

Indoor/outdoor Unit Installation Diagram

•

This illustration is for explanation purposes only.
The indoor unit will actually face a different way.

CS-V7DKE CU-V7DKE / CS-V9DKE CU-V9DKE / CS-V12DKE CU-V12DKE

Содержание CS-V12DKE

















































































Результаты поиска

Содержание CS-V12DKE

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-V12DKE, Руководство по обслуживанию

Результаты поиска

Содержание CS-V12DKE

Отзывы:

Бренды по названию

Популярные бренды