Panasonic CS-ME7CB1P, Руководство по обслуживанию

Страница: 36 / 69

Liquid side
Gas side
ø 6.35 (1/4") t 0.8
ø 9.52 (3/8") t 0.8
CAUTION
When the wall is hollow,
please be sure to use the
sleeve for tube ass'y to
prevent dangers caused by
mice biting the connecting
cable.
Attaching the remote control holder to the wall
1
2
6
3
4
5
7
8
10
9
11
12
Indoor Unit Accessory Parts
1
2
1
2
1
1
2
1
1
1
2
2
Required Materials
• Read the catalog and other technical materials and prepare the required materials.
Product name Remarks
VP20 (outer diameter ø26); also sockets,
elbows and other parts as necessary
PVC adhesive
For refrigerant piping insulation (foamed
polyethylene with a thickness of 8 mm or more)
For drain piping insulation (foamed polyethylene
with a thickness of 10 mm or more)
4
×
1.5 mm 2 flexible cord, type designation
245 IEC 57 (H05RN-F)
Hanging bolts (M10) (4) and nuts (12), Flat
washers (8) (when hanging the indoor unit)
Rigid PVC pipe
Adhesive
Insulation
Indoor/outdoor connecting cable
Hanging bolt related parts
Other Items to be Prepared (Locally Purchased)
Take into consideration the following contents when creating the blueprint.
Indoor unit installation location Remote control mounting location
The location should be strong enough to support the main unit
without vibration.
There should not be any heat or steam sources nearby.
Drainage should be easy. Avoid locating the drain port close to
ditches (domestic wastewater).
Avoid locations above entrances and exits.
Do not block the intake and discharge.
Select the location so that the cool and warm air spreads
throughout the entire room.
Locate the indoor unit at least 1 m or more away from a TV, radio,
wireless equipment, antenna cables and fluorescent lights, and 2
m or more away from a telephone.
Note that if the air conditioning unit is installed near an
electronically lit fluorescent light (inverter, rapid start type, etc.),
it may not receive the remote control signals.
Signals may not be transmitted and received correctly when
the remote control is operated while in the holder. Take the
remote control in your hand to operate the unit.
Mount the holder in a location that is not subject to the
effects of heat (direct sunlight and stoves, etc.).
Selecting the Installation Location
1
Selecting the Piping
2
To Drill a Hole in the Wall and
Install a Sleeve of Piping
3
1. Insert the piping sleeve to the hole.
2. Fix the bushing to the sleeve.
3. Cut the sleeve until it extrudes
about 15 mm from the wall.
4. Finish by sealing the sleeve with
putty or caulking compound at the
final stage.
• Prepare the piping set shown in the table
below or equivalent products for the
refrigerant piping.
* See the Outdoor Unit Installation
Instructions.
Remote control holder
fixing screws
Remote control
holder
Remote
control 3
5
6
Bushing for
tube ass'y
15 mm
Outdoor Indoor
Wall
Sleeve for
tube ass'y
ø70 through
hole
Putty or caulking
compound
Approx.
5 - 7 mm
Piping
insulation
Band
Remote control
Battery
Remote control holder
Drain hose insulation
Receiver
Remote control holder
fixing screw
Receiver cover
Clamp
Clamp mounting screw
Receiver mount
No. No. Accessory part Accessory part Qty. Qty.
CS
-M
E
7C
B
1P
/
C
S
-M
E
10CB1
P
/
CS
-M
E
12CB1
P
/
CS
-M
E
14CB1
P
/
CS
-M
E
10CD3
P
/
CS
-M
E
14
CD3P
36