manualshive.com logo in svg

Panasonic CS-E9SD3UAW, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CS-E9SD3UAW Скачать руководство пользователя страница 10

10 

MODEL 

INDOOR CS-E12SD3UAW 

OUTDOOR

 

CU-E12SD3UA 

Piping 

Pipe Diameter (Liquid / Gas) 

mm (inch) 

6.35 (1/4) / 12.70 (1/2) 

Standard Length 

m (ft) 

7.5 (24.6) 

Length Range (min - max) 

m (ft) 

3 (9.8) ~ 20 (65.6) 

I/D & O/D Height Different 

m (ft) 

15 (49.2) 

Additional Gas Amount 

g/m (oz/ft) 

20 (0.2) 

Length for Additional Gas 

m (ft) 

7.5 (24.6) 

Drain Hose 

Inner Diameter 

mm/inch  

16 / 0.63 

Length 

mm/inch 

117.5 / 4.63 

Indoor Heat 

Exchanger 

Fin Material 

 

Aluminium (Pre Coat) 

Fin Type 

 

Slit Fin 

Row x Stage x FPI 

 

3 x 12 x 18 

Size (W x H x L) 

mm 

590 x 282 x 38.1 

Outdoor Heat 

Exchanger 

Fin Material 

 

Aluminium (Blue Coat) 

Fin Type 

 

Corrugated Fin 

Row x Stage x FPI 

 

2 x 24 x 17 

Size (W x H x L) 

mm 

36.4 x 504 x 824:794 

Power Supply 

 

Outdoor Power Supply 

Power Supply Cord 

A 

Nil 

Thermostat  

Electronic 

Control 

Protection Device 

 

Electronic Control 

 

Dry Bulb 

Wet Bulb 

Indoor 

Operation 

Range 

Cooling 

Maximum °C/°F 

32 / 89.6 

23 / 73.4 

Minimum °C/°F 

16 / 60.8 

11 / 51.8 

Heating 

Maximum °C/°F 

30 / 86.0 

- / - 

Minimum °C/°F 

16 / 60.8 

- / - 

Outdoor 

Operation 

Range 

Cooling 

Maximum °C/°F 

46 / 114.8 

26 / 78.8 

Minimum °C/°F 

-17.8 / 0 

- / - 

Heating 

Maximum °C/°F 

24 / 75.2 

18 / 64.4 

Minimum °C/°F 

-20 / -4 

-21 / -5.8 

 
1. 

Cooling capacities are based on indoor temperature of 27°C Dry Bulb (80.6°F Dry Bulb), 19.0°C Wet Bulb (66.2°F Wet Bulb) and outdoor air 
temperature of 35°C Dry Bulb (95°F Dry Bulb), 24°C Wet Bulb (75.2°F Wet Bulb) 

2. 

Heating capacities are based on indoor temperature of 20°C Dry Bulb (68°F Dry Bulb) and outdoor air temperature of 7°C Dry Bulb 
(44.6°F Dry Bulb), 6°C Wet Bulb (42.8°F Wet Bulb) 

3  Heating low temperature capacity, Input Power and COP measured at 230 V, indoor temperature 20°C (68°F), outdoor 2/1°C (35°F/33.8°F) 

4  Heating extreme low temperature capacity, Input Power and COP measured at 230 V indoor temperature 20°C (68°F), outdoor -7/-8°C  

 (19.4°F/17.6°F) 
5. 

Standby power consumption 

≤

0.7W (when switched OFF by remote control, except under self protection control). 

6. 

Specifications are subjected to change without notice for further improvement. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание CS-E9SD3UAW





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды