51
CQ-VX1300W
1
E
N
G
L
I
S
H
50
CQ-VX1300W
37
E
N
G
L
I
S
H
38
Specifications
General
Power Supply
: 12 V DC (11 V - 16 V), test voltage 14.4 V, negative ground
Current Consumption
: Less than 8.5 A (CD play mode)
Rated Output
: 16 W x 4 ch (1 kHz, 1%, 4
Ω
)
Maximum Power Output
: 41 W x 4 ch
Suitable Speaker Impedance
: 4
Ω
Audio Input Impedance
: 10 k
Ω
(AUX IN)
Audio Input Voltage
: Max. 2 V (AUX IN)
Pre-out Output Voltage
: 1.8 V
Pre-out Output Impedance
: 600
Ω
Dimensions (W x H x D)
: 178 x 100 x 160 mm
Weight
: 2.4 k
g
DSP
Number of Channels
: 2 input channels, 4 output channels
Space mode
: 7 mode
Equalizer Center Frequency
: 80, 160, 320, 640, 1.6 k, 4 k, 10 k (Hz)
Variable Range of Equalizer
: –12 to +12 dB (13 steps)
FM Stereo Radio
Frequency Range
: 87.50 - 108.00 MHz
Usable Sensitivity
: 12 dBf.
Total harmonic distortion (mono)
: 0.3 % (1 kHz)
Weighted S/N ratio (mono)
: 70 dB
Frequency Response
: 20 Hz – 15 kHz (± 3 dB)
Stereo Separation
: 42 dB (at 1 kHz)
Image response ratio
: 75 dB
AM Radio
Frequency Range
: 531 kHz - 1,602 kHz
Usable Sensitivity
: 27 dB/µV
Image response ratio
: 65 dB
CD Player
Channel
: 2 channels
Quantization
: 16-bit linear
Frequency Response
: 5 Hz - 20 kHz
Dynamic range
: 90 dB (IHF, A)
Wow and Flutter
: Below measurable limits
Cassette Tape Player
Reproduction system
: 4-track, 2-program stereo
Tape Speed
: 4.76 cm/sec
Fast Forward Time
: 100 sec (C-60)
Rewind Time
: 100 sec (C-60)
Wow and Flutter
: 0.07 % (WRMS)
Signal/Noise Ratio
: Dolby B NR OFF 56 dB (IHF, A)
Dolby B NR ON 66 dB (IHF, A)
Frequency Response
: 30 Hz - 18 kHz (normal tape)
30 Hz - 20 kHz (metal tape)
Note
: Specifications and the design are subject to modification without notice due to improvements in technology.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol
B
are trademarks of Dolby Laboratories Licensing Corporation.
Reset Switch
Reset switch
Insert a hard, slender stick into the hole and push the switch.
The unit returns to the default state when the trouble is reset.
Remember, the data and settings stored in the memory are
deleted.
Important
Push the switch only when the unit fails to operate with any but-
tons.
If the unit fails to return to normal condition, contact the shop
where you purchased this product and ask for repairs.
CD EJECT
CST EJECT
CD IN
CST IN
G
INTEGRATED CD/CASSETTE RECEIVER WITH
u
u
RESET
Maintenance
(continued)
Speaker Connections
Caution:
Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers.
L
R
-
-
-
-
-
-
-
-
-
-
+
+
+
+
+
+
+
+
+
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
L
R
L
R
L
R
<Right>
<Wrong>
(White)
(White
w/black stripe)
Chassis
(Gray
w/black stripe)
(Gray)
Chassis
¡
Use ungrounded speaker only.
¡
The maximum speaker output should be 41 W or more. (If used with
the optional power amplifier, the speaker output should be higher than
the maximum amplifier output.)
¡
The speaker impedance should be 4 - 8
Ω
.
¡
This unit uses the BTCL circuit, so each speaker should be connected
separately using parallel vinyl insulated cords.
¡
The speaker cords and the power amplifier unit should be kept away
(about 30 cm apart) from the antenna and antenna extension cord.
¡
Never connect the speaker cord to
the body of the car.
¡
Do not use a 3-wire type speaker
system having a common earth
lead.
¡
Do not connect more than one
speaker to one set of speaker
leads.
