34
35
27
E
N
G
L
I
S
H
28
E
N
G
L
I
S
H
CQ-C3400/C3300/C3100W
CQ-C3400/C3300/C3100W
How to hold the disc
¡
Do not touch the underside of the disc.
¡
Do not scratch the disc.
¡
Do not bend the disc.
¡
When not in use, keep the disc in the case.
Do not use irregularly shaped discs.
Do not leave discs in the following places:
¡
Direct sunlight
¡
Near car heaters
¡
Dirty, dusty and damp areas
¡
Seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write anything on the disc label with a pointed pen or
hard-point pen.
Notes on Discs
Notes on CD/CD Media (CD-R, CD-RW, CD-ROM)
Label side
<Correct>
<Wrong>
Do not use irregularly shaped discs.
Notes on CD-Rs/RWs
¡
You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due to
their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
¡
CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage and make playback impossible.
¡
Some CD-R/RWs can not be played back successfully thanks to incompatibility among writing software, a CD recorder
(CD-R/RW drive) and the discs.
¡
This player cannot play the CD-R/RW discs if the session is not closed.
¡
This player cannot play the CD-R/RW discs which contains other than CD-DA data or MP3/WMA data (Only for CQ-
C3400/C3300W).
¡
Be sure to observe the instructions of CD-R/RW disc for handling it.
If you use commercial CDs, they
must have either of these labels
shown at right.
TEXT
(Only for CQ-C3400/C3300W)
Troubleshooting
If You Suspect Something Wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is rec-
ommended to consult the shop where you purchased the prod-
uct. The product should be serviced only by qualified personnel.
Caution:
¡
Do not use the unit in an irregular condition,
for example, without sound, or with smoke or
foul smell, which can cause ignition or electric
shock. Immediately stop using the unit and
call the store where you purchased it.
¡
Never try to repair the unit by yourself
because it is dangerous to do so.
■
Common
BALANCE/FADER setting is not appropriate.
a
Readjust BALANCE/FADER.
There is a break, a short circuit, poor contact or wrong wiring regarding the
speaker wiring.
a
Check the speaker wiring.
No sound from
speaker(s)
Some operations are not executable in particular modes such as menu mode.
a
Read the operating instructions carefully and cancel the mode. In case
the unit is still out of order, consult your dealer.
Some operations are
not executable.
Alternator noise comes from the car.
a
Change the wiring position of the ground lead.
a
Mount a noise filter on the power supply.
Noise is made in step
with engine revolu-
tions.
There is an electromagnetic-wave generator such as a cellular phone near the
unit or its electrical lines.
a
Keep an electromagnetic-wave generator such as a cellular phone away
from the unit and the wiring of the unit. In case that noise cannot be
eliminated due to the wiring harness of the car, consult your dealer.
The contact of the ground lead is poor.
a
Make sure that the ground lead is connected to an unpainted part of the
chassis securely.
Noise
You cannot operate the unit while the demonstration screen appears.
a
Press [DISP] to end the demonstration screen.
If the demonstration screen appears frequently, there is a possibility that poor
contact or wrong wiring arises between the battery lead of the unit and the
battery cable of the car. (The battery lead should be always powered.)
a
Check the battery wiring in accordance with the wiring diagram.
The demonstration
screen displayed and
no operable
MUTE is set to ON.
a
Set MUTE to OFF.
The wiring of speaker lines are not correct, or a break or poor contact arises.
a
Check the wiring in accordance with the wiring diagram.
Sound is not
generated.
The power cord (battery, ACC and ground) is connected in the wrong way.
a
Check the wiring.
Fuse blowout
a
Eliminate the cause of fuse blowout and replace the fuse with new one.
Consult your dealer.
No power to the unit
Problem
Possible cause
a
Possible solution
