10
CQ-C9901W/C9801W
11
English
CQ-C9901W/C9801W
Preparation
Note:
Adjust the clock when “ADJUST” appears on the
display.
1
Press
[MENU]
to display the menu dis-
play.
For using the remote control, hold down
[MENU]
for 2 sec. or more.
2
Press
[
]
]
or
[
[
]
to display the DIS-
PLAY menu.
3
Press
[
{
]
to select “CLOCK ADJ”.
4
Press
[BAND]
(
SET
) to confirm the dis-
play.
5
Adjust the setting value.
[
[
]
: Adjusting minutes
[
]
]
: Adjusting hours
[
}
]
: Forward
[
{
]
: Backward
6
Press
[BAND]
(
SET
) to confirm the
adjustment.
Note:
For cancellation of clock adjustment, press
[DISP]
.
7
Press
[MENU]
.
For using the remote control, hold down
[MENU]
for 2 sec. or more.
When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP]
to change to regular mode.
1
Set your car’s ignition switch to the ACC
or ON position.
The demonstration screen appears.
Example:
CQ-C9901W
2
Press
[DISP: DISPLAY]
.
The demonstration screen is cancelled, and no more
appears.
Note:
If you would like to turn on the power and make
the demonstration message appear, hold down
[SRC]
(
PWR: POWER
) for 4 sec. or more.
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡
Subwoofer level adjustment (
a
page 32)
¡
Subwoofer low pass filter (
a
page 32)
Connecting an AV device (TV, VTR)
If you connect TV to AUX1 terminal, set the AUX1 setting
to TV.
1
Press
[SRC: SOURCE]
to select the
AUX1 mode.
(
a
page 14)
2
Press
[MENU]
to display the menu dis-
play.
For using the remote control, hold down
[MENU]
for 2 sec. or more.
3
Press
[BAND]
(
SET
) to adjust.
: TV
: Other devices (Default)
Note:
When using an external TV unit manufactured by
a third party, select the
TV
mode.
4
Press
[MENU]
to confirm the adjust-
ment.
The following functions are activated when the Security
Function is ON. (
a
page 34)
¡
The security indicator blinks when removing the face
plate.
¡
The alarm sounds and the message appears on the
screen to warn you to remove the face plate at power
off.
Security Indicator
SRC
CS
Preparation
First T
ime Power On
(DEMONSTRATION)
Remote Control Preparation
Security Function
Setting
Other Settings
Clock adjustment
(CLOCK ADJ: CLOCK ADJUSTMENT)
Battery Replacement
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Warning
¡
Keep batteries and insulation film out of reach
of infants. If an infant ingests a battery, please
seek immediate medical attention.
Caution
¡
Remove and dispose of an old battery immediately.
¡
Do not disassemble, heat or short a battery.
Do not throw a battery into a fire or water.
¡
Follow local regulations when disposing of a
battery.
¡
Improper use of a battery may cause overheat-
ing, an explosion or ignition, resulting in injury
or a fire.
Note:
¡
Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under nor-
mal use (at room temperature)
q
w
q
Remove the battery holder
with the remote control unit
placed on a flat surface.
q
Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w
Pull it out in the direction
of the arrow using a
tough pointed object.
w
Put a battery in the case with
(+)-side facing up.
e
Put the case back.
2
3
Tough pointed object
Back side
Insulation film
