5
@9
Focus Reverse Switch
[FOCUS REVERSE, NOR/REV]
Changes the operating direction of FOCUS Lever
!99
.
The lens is focused far when FOCUS Lever
!9
is moved
toward FAR, or near when the lever is moved toward
NEAR, provided that FOCUS REVERSE Switch
@9
is in
the NOR position. When FOCUS REVERSE Switch
@9
is set to the REV position, the lens focus operates in the
opposite direction.
With FOCUS REVERSE Switch
@9
in the REV position,
the operating directions shown on the panel are oppo-
site to the indications on the panel. In this case, paste
the supplied seal on the panel.
#0
Tilt Reverse Switch [TILT REVERSE, NOR/REV]
Changes the tilt direction controlled by PAN/TILT Lever
@0
. The pan/tilt head turns up when PAN/TILT Lever
@0
is moved toward UP, or down when it is moved toward
DOWN, provided that TILT REVERSE Switch
#0
is in
the NOR position. The pan/tilt head moves in the oppo-
site direction if the TILT REVERSE Switch
#0
is in the
REV position.
With TILT REVERSE Switch
#0
in the REV position, the
operating directions shown on the panel are opposite to
the indications on the panel. In this case, paste the sup-
plied seal on the panel.
#1
Pan Reverse Switch [PAN REVERSE NOR/REV]
Changes the pan direction controlled by PAN/TILT
Lever
@0
. The pan/tilt head turns leftward when PAN/
TILT Lever
@0
is moved toward LEFT, or rightward if it
moved toward RIGHT. The rotary head turns in the
opposite direction if the PAN REVERSE Switch
#1
is in
the REV position, provided that PAN REVERSE Switch
#1
is in the NOR position. When PAN REVERSE
Switch
#1
is set to the REV position, the pan/tilt head
turns in the opposite directions.
With PAN REVERSE Switch
#1
in the REV position, the
operating directions shown on the panel are opposite to
the indications on the panel. In this case, paste the sup-
plied seal on the panel.
Note: TILT REVERSE Switch
#0
and PAN REVERSE
Switch
#1
may be used to reverse the operating
direction of the pan/tilt head, but be sure to set the
operating direction of the pan/tilt head with its
mounting direction selection switch during its instal-
lation depending on whether the pan/tilt head is
mounted on the floor or is suspended. Unless the
mounting direction selection switch on the pan/tilt
head is properly set, the pan/tilt head will pan or tilt
in the opposite direction and the pan/tilt head opera-
tion limiters will not be properly stored in the memo-
ry. For details on the setting of this switch, refer to
the INSTALLATION OF PAN/TILT HEAD at page 5.
• Install the pan/tilt head after carefully reading the
Operating Instructions for Pan/tilt Head.
• Have four hex bolts (M6 x 4) ready for mounting the
pan/title head. Select bolts of a length appropriate to the
material and structure of the mounting base and the
overall weight applied to it. Fasten the bolts securely
with plain washers, spring washers, and hex nuts. If the
bolts are not securely tightened, the pan/tilt head might
fall to cause injuries or accidents. In case of suspending
the pan/tilt head, locally purchase a wire rod strong
enough to hold the pan/tilt head, camera, and lenses,
pass it through the wire hole opened in a firm board,
such as of the ceiling, for example, and fasten it secure-
ly.
• The switches on the pan/tilt head have been preset
before shipment from the factory on the assumption that
the pan/tilt head would be suspended from the ceiling. If
the pan/tilt head is mounted on a board, for example, be
sure to shift the mounting direction switches on the
pan/tilt head. Unless this is done, pan/tilt directions will
be reversed and pan/head operation limiter data cannot
be properly stored in the memory. For details on shifting
these switches, refer to the Operating Instructions for
Pan/tilt Head.
●
Changing Switch Settings on Pan/tilt Head
q
Remove the cover from the pan/tilt head.
* Be careful of the Tally Indicator wire.
INSTALLATION OF PAN/TILT
HEAD
w
Shift the mounting direction switches (SW1, SW2) on
the pan/tilt head depending on whether the head is sus-
pended from the ceiling or mounted on the floor. They
are originally set for suspended installation.
* Do not shift SW3, which is originally set to P/T CON-
TROL SERIAL. If SW3 is shifted from the original posi-
tion, no operations can be controlled from the control
panel.
Tally Indicator
