Panasonic AV-HS60C3G, Руководство по эксплуатации

Страница: 51 / 176

– 51 –
Chapter 5 Basic Operations — Background transition
Background transition
Selecting a bus
Select sources to be used for background transitions.
1
Press the crosspoint buttons.
f
Depending on the operating status, the buttons pressed will light in one of three color patterns.
Type Color when lit* Description
High tally [Red] Lights when the selected source is included in the on-air output.
Low tally [Yellow]
Lights when the selected source is not included in the on-air output but
included in the program output.
Preset tally [Green]
Lights when the selected source is included in neither the on-air output
nor the program output.
* Indicates the default colors. To change the colors, select the <PANEL> button on the top menu → [BUTTON COLOR] → [Settings] tab → [Select Button]
column.
f
The color when lit for the buttons not selected can also be set by source or by block. (page 129)
Selecting a bus using the SHIFT function
The SHIFT function is to switch pages of the crosspoint buttons with the <2nd PAGE>/<3rd PAGE> button.
There are two ways to perform the SHIFT function.
All SHIFT
Use the <2nd PAGE>/<3rd PAGE> button to switch all pages of buses included in the corresponding ME at once.
(page 25)
Single SHIFT
Assign the <2nd PAGE>/<3rd PAGE> button to the crosspoint buttons to switch pages. (page 115)
Using the assigned button, only the pages of individual bas can be switched.
The <2nd PAGE>/<3rd PAGE> buttons are available in two modes. The setting can be changed using the menu. (page 118)
[Normal] The buttons are turned on only while they are pressed.
[Page Lock] The buttons are turned on and off each time they are pressed.
Selecting the bus mode
Set the bus operating mode.
(
page 118
)
1
Select the <OPR> button → [OTHER SETTINGS] → [Bus Mode] tab.
2
Set an item in [Bus Mode] in the [Bus Mode] column.
[A/B]
When the fader lever is at side A, the signals selected on the A bus are used as the source of the PGM bus.
When the fader lever is at side B, the signals selected on the B bus are used as the source of the PGM bus.
[PGM-A/PST-B]
Using a flip-flop system, the signals selected on the A bus are always used as the source of the PGM bus, and the
signals selected on the B bus are always used as the source of the PST bus.
[PGM-B/PST-A]
Using a flip-flop system, the signals selected on the B bus are always used as the source of the PGM bus, and the
signals selected on the A bus are always used as the source of the PST bus.
Transition operations
Operate transitions using the transition area on the Control Panel.
1
Select the transition type.
f
Use the transition type selection buttons. (page 26)
2
Execute the transition using the fader lever or the transition execution button.
Manual transition Move the fader lever to execute the transition.
Auto transition Press the <AUTO> button to execute the transition automatically.
Cut transition Press the <CUT> button to execute the transition instantaneously.
f
The lighting of the bus name display panel to the right of the PGM/A bus crosspoint buttons and PST/B bus crosspoint buttons, whether High tally
color or Low tally color, indicates the output status of the buses.
Lighting color Description
High tally Lights when the relevant bus is included in the on-air output.
Low tally Lights when the relevant bus is not included in the on-air output but included in the program output.
Off
Lights when the relevant bus is included in neither the on-air output nor the program output.
r
Setting the transition time
1
Select the <ME1>/<ME2> button
→
[BKGD]
→
[Transition] tab.
2
Select [AUTO Time] in the R menu, and set [AUTO Time] in the encoder menu.