manualshive.com logo in svg

Panasonic AJD440 - DVCPRO PLAYER, Руководство по обслуживанию

Поделиться
Скачать
Panasonic AJD440 - DVCPRO PLAYER Скачать руководство пользователя страница 41

2-24

1. Press and Lift up to A/C Head lightly as indicated

as figure position, then confirm that the CTL and
CUE output level is within specification.

2. If it out of spec., loosen the screw H and adjust

the screw B until Cue output is maximized.

3. When confirm the level in specification, screw (H)

should be tighten completely. (refer to A/C Head
Adjustment Method)

4. Adjust alternately with other A/C head

adjustments (Azimuth, X-Value).

3-16.  A/C Head Tilt Confirmation

SPEC

A/Amax 

≥

 0.8

TEST

POINT

CUE AUDIO :
Refer to item “2. Table of Test Point”

ADJ.

SCREW A, G (A/C Head)

MODE

PLAY

TAPE

NTSC : VFM3580KM or VFM3580KL

(14 to 22min)

PAL : VFM3680KM or VFM3680KL

(14 to 22min)

TOOL

VFK1178, VFK1148 (Hex Driver)

1. Playback the Alignment tape.
2. Confirm that the screw G and H are not loosened.
3. Push the tension post follow the arrow (B)

direction as shown in figure as range of T2 post
does not move. And confirm that the CUE output
level is within specification.

4. If out of specification, loosen the screw G and

adjust the screw A, then tighten the screw G with
10cN-m (1.0kg) torque.

5. The final touch of the adjustment must be turned

clockwise. After this adjustment, confirm that the
screw A is not loosened.

6. If adjust the screw A, Confirm that the tape pass

condition follow Post Limit Confirmation
procedure (item 3-12).

 ( Increase
  tension )

B

Содержание AJD440 - DVCPRO PLAYER









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды