manualshive.com logo in svg

Panasonic AJD440 - DVCPRO PLAYER, Руководство по обслуживанию

Поделиться
Скачать
Panasonic AJD440 - DVCPRO PLAYER Скачать руководство пользователя страница 39

2-22

1. With Tilt and Azimuth adjustment, loosen screw

(G) first and tighten screw (G) after finish
adjustment. And if turn screw (A) and (F) too
much for adjustment, tighten screw (A), (F) and
(G) alternately.

Figure 3-13-1

2. Perform the Height and X-value adjustment under

the screw (G) tighten completely.

3. Be careful the tape damage at T3 Post, when

adjust tilt of A/C Head. (refer to figure 3-13-1)

Figure 3-13-2

4. Confirm the screw (A) does not loosen, before

execute the A/C Head Tilt adjustment. The screw
(A) should be always touch to top of A/C Head.

5. When the height of A/C Head is adjusted by Nut

(B), first the screw (H) should be loosen. And after
height adjustment finished, tighten the screw (H)
lightly.

Figure 3-13-3

6. After finish X value adjustment, hit the portion (L)

lightly and confirm the specification of X-value.

7. Each adjustment of A/C Head should be finished

at the condition of turn the each adjustment screw
tighten direction. And hit the portion (L) lightly for
remove the distortion of A/C Head plate.

Figure 3-13-4

A/C Head

Lift up portion

Press down
portion

A/C Head

A/C Head

(L)

Содержание AJD440 - DVCPRO PLAYER









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды