Panasonic AGM1CSEC16P Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 126

background image

7.1 Preparation of the SD Memory Card and SDHC Memory Card

■

Usable SD memory card and SDHC memory cards

We recommend SLC SD Memory Cards and SLC SDHC Memory Cards.

Logo printed on the GM1
Controller (RTEX-compatible /
EtherCAT-compatible)

Usable SD (SDHC) memory cards

Card type

Capacity

SD memory card

2 GB

SDHC memory card

4 GB to 32 GB

■

Precautions on handling the SD memory card and SDHC memory card

The data saved in the SD memory card or in the SDHC memory card may be lost in the

following cases. We assume no responsibility whatsoever for the loss of saved data.

● When the user or a third party has misused the SD memory card or SDHC memory card
● When the SD memory card or SDHC memory card was affected by any static electricity or

electrical noise

● When the SD memory card or SDHC memory card was taken out, or the power supply to the

GM1 Controller (RTEX-compatible / EtherCAT-compatible) was turned OFF, while the card

was being accessed to save or delete data

● It is recommended to save important data in another media for backup.
● Never remove the card or turn OFF the power supply to the GM1 Controller (RTEX-

compatible / EtherCAT-compatible) while the "SD" LED on the GM1 Controller (RTEX-
compatible / EtherCAT-compatible) is lit (data is being read from or written into the card).
Data may be damaged.

● Do not use an SD memory card or SDHC memory card that has a memory capacity

larger than the usable capacity. Data in the card may be damaged.

■

Formatting the SD memory card and SDHC memory card

In principle, the SD memory card and SDHC memory card have been formatted by the time of

purchase, and no formatting by the user is required. If formatting becomes necessary,

download the SD formatter software from the SD association site and format the memory card.

● The SD memory card or SDHC memory card file system formatted by PC’s standard formatting

software does not satisfy the SD memory card or SDHC memory card specifications. Please
use the dedicated formatting software.

7.1 Preparation of the SD Memory Card and SDHC Memory Card

7-2

WUME-GM1H-02

«
...
70
71
72
73
74
...
»

Содержание AGM1CSEC16P































































































































Отзывы:

Нет отзывов

Похожие инструкции для AGM1CSEC16P

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Eaton Страницы: 86

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 36

Бренд: GCE Страницы: 24

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: UniPOS Страницы: 51

Бренд: Unipulse Страницы: 126

Бренд: YachtSafe Страницы: 3

Бренд: Newport Страницы: 417

Бренд: Casambi Страницы: 2

Бренд: MaintTech Страницы: 28

Бренд: Bender Страницы: 28

Бренд: Hirschmann Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды