background image

— 11 —

Page 11

June 5, 2002 1:41 pm

It may be unlawful to record or play back copyrighted material 
without the consent of the copyright owner.

Accidental erasure prevention

To prevent accidental recording on a 
recorded cassette, remove its record 
safety tab. To record on it later, cover 
the hole with adhesive tape.

Basic Recording

A

Load a cassette

Make sure the record safety tab is intact. If not, cover the hole with 
adhesive tape before inserting the cassette.

The VCR turns on, and the counter on the on-screen display is 
reset, automatically.

B

Select recording channel

Press 

CH+/–

 or the 

Number keys

 on the Remote. Or push the 

JOG

 

dial, then turn it to the left or right.

If you connect the TV and the VCR only using the RF 
connection (

pg. 6), press 

TV/VCR

 on the Remote so that the 

VCR mode indicator lights on the display panel, to view the 
program to be recorded.

C

Set tape speed

Press 

SP/EP

. The selected tape speed will appear on the TV screen.

NOTE:

You can select tape speed in the stop mode or during recording 
pause mode.

D

Start recording

On the VCR, press 

REC

 (

7

). Or on the Remote, while holding 

REC

 

(

7

), press 

PLAY

 (

4

).

NOTE:

If “VIDEO CALIBRATION” is set to “ON” (

pg. 14) (default 

setting), the VCR takes about 7 seconds to assess the quality of the 
tape in use, then recording begins with the picture level 
optimized.

NOTE:

If the tape reaches its end during recording, the recording stops 
and “ 

” and “ 

$

” on the display panel blink. Press 

STOP/EJECT

 

(

0

) on the VCR to eject the cassette or press 

REW

 (

3

) on the 

Remote to rewind the tape.

Recording Features

Specifying recording length
— Instant Timer Recording (ITR)

During recording, press 

REC

 (

7

) on the VCR repeatedly until the 

recording length you want appears on the display panel. The 
record indicator (

) on the display panel starts blinking.

Each time you press the button, recording length increases in 
30-minute intervals (up to 6 hours).

The VCR shuts off after recording is finished.

To cancel an ITR, press 

STOP

 (

8

) on the Remote or 

STOP/EJECT

 

(

0

) on the VCR.

Watching one program while recording another

During recording...

If you connect the TV and the VCR only using the RF 
connection (

pg. 6) to view pictures from the VCR, press 

TV/

VCR

 on the Remote so that VCR mode indicator goes off from 

the display panel. (The TV broadcast being recorded 
disappears.)

If you are using the AV connection (

pg. 6) to view pictures 

from the VCR, change the TV’s input mode from AV to TV.

Then, select the channel you want to watch, on the TV.

Tape remaining Time

Press – –:– – to display the tape remaining time on the screen.

NOTES:

Set “SUPERIMPOSE” to “ON” to display the indications on the 
screen. (

pg. 15)

Depending on the type of tape used, the tape ramaining time 
may not appear right away, or is not correct, “  –:– –” may 
sometimes appear, or the display may blink on occasion. 

Second Audio Recording

This VCR’s built-in MTS decoder enables reception of 
Multichannel TV Sound broadcast. To record a SAP program 
received, set “2ND AUDIO RECORD” to “ON” (

pg. 15).

S-VHS (Super VHS), S-VHS ET or VHS Recording 
Mode

This VCR can record in S-VHS (Super VHS), S-VHS ET or VHS.

To record in S-VHS:

Set “S-VHS MODE” to “ON” (

pg. 15). Then, insert a cassette 

marked “S-VHS”. The S-VHS indicator lights up on the display 
panel.
The S-VHS recording mode is selected.

To record in S-VHS ET on a VHS cassette:

Set “S-VHS ET” to “ON” (

pg. 14). Then, insert a cassette 

marked “VHS”. The S-VHS indicator lights up on the display 
panel.

To record in VHS:

Insert a cassette marked “VHS”.
Set “S-VHS ET” to “OFF” (

pg. 14).

To record in VHS on an S-VHS cassette:

Insert a cassette marked “S-VHS”. The S-VHS indicator lights up 
on the display panel. Then, set “S-VHS MODE” to “OFF” 
(

pg. 15). The S-VHS indicator goes off.

The VHS recording mode is selected.

NOTE:

When playing back a tape that has been recorded in S-VHS or 
S-VHS ET, the S-VHS indicator lights up on the display panel 
regardless of the “S-VHS ET” or “S-VHS MODE” setting. 
(

pg. 14, 15)

Recording

During recording

Pause recording

Press 

PAUSE

 (

9

).

Press 

PLAY

 (

4

) to resume recording.

You can select channel in the recording pause mode.

Stop recording

Press 

STOP

 (

8

) on the 

Remote.

OR

Press 

STOP/EJECT

 (

0

) on 

the VCR.

Record safety tab

AG-3200P-EN.fm  Page 11  Wednesday, June 5, 2002  1:43 PM

Содержание AG-3200P

























Отзывы: