background image

Panamorph DC1 User Manual and Installation Guide, Version 1.1, copyright February, 2011.  All rights reserved. 

Page 7 

2.

  Using the included gold hex key, install the six 7/8” socket head screws each through a 3/8” 

aluminum spacer and into the six threaded holes from the ceiling side of the attachment plate.  
Thread only enough to extend the screw to the bottom of the plate.   
 

3.

  Insure that the RPA000 mount head is secure (see instructions included with the RPA000 mount) 

and oriented properly relative to the 7/8” socket head screw heads so that the mounted projector will 
face the screen.  Use two people to lift and position the projection assembly so that the heads of each 
of the 7/8” socket head screws rest within the matching final location of the RPA000 mount head.  At 
this point the silver 3/8” spacers should be between the Attachment Plate and the RPA000 mount 
head.  The projection assembly may be lowered to allow the 7/8” screw heads to rest on the RPA000 
mount.  However, a first person should continue to guide the projection assembly while and a second 
person uses the gold assembly wrench to tighten the 7/8” screws.  When tightening these screws, do 
so in a pattern of incrementally driving each screw a little more into the attachment plate so that at 
any time the projection assembly is resting on as many screw heads as possible until all are 
tightened. 
 
If the lens must be removed for any length of time it is recommended that a similar weight be 
suspended from the front of the attachment kit to balance the weight of the projector.  This will 
minimize unusual stresses on the ceiling mount system.

  

 

 
ALTERNATE AK8PRO ATTACHMENT PLATE METHOD 

For Larger Projectors Requiring Support Chains (See compatibility list on Page 5 and Page 7) 
(Phillips screwdrivers, pliers, scissors and appropriate ceiling hooks required)

 

 

 

 

 

1.

  Install the Plate Hook Assemblies in the two “H” 

holes of the Attachment Plate (see diagram) with the 
hook ends on the ceiling side as shown above.  Use 
pliers to bend the closed hooks apart just enough to 
install a Chain End (See Step 5). 

 

2.

  Position the projector bottom-up.  Consult the 

Attachment Plate Diagram for plate orientation, hole 
positions, and required screws and spacers for your 
projector model.  Insert and tighten the required 
screws through the ceiling mount adapter (not included), then through the designated holes of the 
Attachment Plate, and then through any required spacers and finally into the projector ceiling mount 
holes.  

If the screws in the kit are not long enough, procure the longest metric screws you can 

for the safest installation.

 

Plate Hook Bag Contents (AK6 only) 

3/16” Chain (6 feet) 

Chain End (4) 

Plate Hook  

as assembled to 

Attachment Plate 

#8-32 Wire Hook (2) 

#8-32 Nut (4) 

#8 Washer (4) 

M4 Lock Washer (2) 

Ceiling 

side 

Attachment 

Plate 

Ceiling Mount 

adapter 

Attachment 

Screws 

Spacers 

Содержание AK8Pro-L











Отзывы: