Panametrics DewPro MMY30 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 43

Panametrics DewPro MMY30 Скачать руководство пользователя страница 11

DewPro

®

MMY30 User’s Manual

3

Chapter 1. General System Information

1.3 Introduction

1.3.1

Unit Description

The DewPro MMY30 trace moisture transmitter (shown in

below) is a loop-powered dewpoint measuring

device. The transmitter includes a sensor element, a flow chamber, a weather-proof enclosure, microprocessor

electronics, and assorted fittings, all in a compact assembly. In most cases, either the inlet or outlet port includes an

orifice to regulate the flow. The placement of this orifice determines whether the dewpoint measurement is done at

process (line) pressure (outlet orifice), or at atmospheric pressure (inlet orifice). A 2 micron sintered inlet filter

prevents solid particles from entering the device.

Figure 2: DewPro MMY30 Transmitter

1.3.2

Optional Display/User Interface

The optional display/user interface feature allows the MMY30 to be configured to the user's specifications. See

Chapter 4

for more information.

«
...
9
10
11
12
13
...
»

Содержание DewPro MMY30












































Отзывы:

Нет отзывов