background image

1                 2                 3                4                5             

    6                 7                8

UNSAFE VOLTAGE

    BREAKER

      WIRING FAULT

  TEMPERATURE

20 A

BRIGHTNESS

OUTLET STATUS

REBOOT 1                       REBOOT 2

M4320-PRO

B LT

Blue

 

ENABLED

   VOLTS

Power Management with Control System Interactive Functionality.

• 20 Amp Capacity M4320-PRO   
  
• 8 Individually Controllable Rear Panel Outlets

• Fully Programmable

• TCP/IP (BlueBOLT™) Installed

• RS-232 Card (Included, not installed) 

• Linear Filtration with 3 Isolated LiFT Filter Banks, 76db (5 kHz - 250 kHz), 46 db (250 kHz - 1 MHz) 

• One Isolated Filter Bank for High Current Devices, 60db (5 kHz - 450 kHz), 46 db (450 kHz - 1 MHz) 

• Front Panel Circuit Breaker

• Integrated Front Rack Ears

• 12 Volt Input Triggering

• Detachable 10 ft. Power Cord - 20A plug

• AVM & Protect-or-Disconnect Circuitry

M4320-PRO Instructions

INS00860 REV. D       5/10

    

Important:

 You will need the BlueBOLT-CV1’s unique MAC address and challenge key (provided on the 2 labels 

attached to the cover of the Quick Start Guide which is included in the M4320-PRO packaging). One label is 
permanently adhered to the Quick Start Guide and the other is removable for your convenience. 

B LT

Blue

ENABLED

Содержание M4320-PRO















Отзывы: