2
Palmgren Operating Manual & Parts List 9683295
GETTING STARTED
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions,
assembly instructions, operating and maintenance procedures, parts
list and diagram. Keep your invoice with this manual. Write the
invoice number on the inside of the front cover. Keep this manual
and invoice in a safe and dry place for future reference.
STRUCTURAL REQUIREMENTS
Make sure all supporting structures and load attaching devices are
strong enough to hold your intended loads. If in doubt, consult a
qualified structural engineer.
ELECTRICAL REQUIREMENTS
The power supply to Palmgren Model 9683295 10˝ × 16˝ Band Saw needs
to be 230 V AC, 3-phase, 6.2 A, 60 Hz.
TOOLS NEEDED
Standard professional mechanic’s hand tool set (socket set, pliers and
spirit level, etc.).
UNPACKING
When unpacking, check to make sure all parts listed below are
included. If any parts are missing or broken, please contact your local
retailer.
IMPORTANT:
Many unpainted steel surfaces have been coated with
a protectant. To ensure proper fit and operation, remove coating.
Coating can be easily removed with mild solvents, such as mineral
spirits, and a soft cloth. Avoid getting solution on paint or any of the
rubber/plastic parts. Solvents may deteriorate these finishes. Use
soap and water on paint, plastic or rubber components. After
cleaning, cover all exposed surfaces with a light coating of oil.
CAUTION:
Never use highly volatile solvents. Non-flammable solvents
are recommended to avoid possible fire hazard.
CONTENTS
• Complete Band Saw
• Depth Stop Rod (for assembly see page 4)
• Operating Instructions
• Chip Tray
UNPACK:
Remove all the over packing materials, but leave unit attached to its
pallet. Do not discard packing materials until after the machine has
been inspected for damage and completeness. Locate loose parts
and set aside.
INSPECT:
After unpacking the unit, carefully inspect for any damage that may
have occurred during transit. Check for loose, missing or damaged
parts. Shipping damage claims must be filed with the carrier.
This machine and its accessories should be visually inspected before
use, in addition to regular periodic maintenance inspections. Be sure
that the voltage labeled on the unit matches your power supply.
SAFETY RULES
WARNING:
For your own safety, read operating instructions manual
before operating tool.
WARNING:
Always disconnect the machine from its power source
before changing blades or carrying out any maintenance procedure,
even in the case of irregular machine operation.
PROPOSITION 65 WARNING:
Some dust created by using power tools
contain chemicals known to the state of California to cause cancer, birth
defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry
products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals;
work in a well ventilated area and work with approved safety
equipment. Always wear
OSHA/NIOSH
approved, properly fitting
face mask or respirator when using such tools
WARNING:
Always follow proper operating procedures as defined in
this manual even if you are familiar with the use of this or similar tools.
Remember that being careless for even a fraction of a second can result
in severe personal injury.
• Dress properly. Do not wear loose clothing, shirts with sleeves
that are too long, gloves that are too big, jewelry or chains as they
can be caught in moving parts. Protective, electrically non-
conductive clothes and non-skid footwear are recommended
when working. Wear restrictive hair covering to contain long hair.
• Use eye and ear protection. Always wear ANSI approved impact
safety goggles.
• Stay alert. Watch what you are doing, use common sense. Do not
operate any tool when you are tired.
• Guard against electrical shock. Prevent body contact with
grounded surface such as pipes, radiators, ranges and refrigerator
enclosures.
• Do not operate tool if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your
judgement or reflexes will be impaired. If there is any doubt, do
not operate the tool.
• Give your work undivided attention. Looking around, carrying on
a conversation and “horse-play” are careless acts that can result in
serious injury.
PREPARE WORK AREA FOR JOB
• Keep work area clean and free of equipment, tools or other
objects. Cluttered areas invite injuries.Keep the floor around the
machine clean and free of scrap material, oil and grease.
• Observe work area conditions. Do not use machines or power
tools in damp or wet locations. Do not expose to rain.
• Keep work areas well-lit. Do not use electrically powered tools in
the presence of flammable gases or liquids.
• Keep children away. Children must never be allowed in the work
area. Do not let them handle machines, tools or extension cords.
• All internal operations, maintenance, or repairs must be
performed in a well-lit area
• Keep visitors a safe distance from the work area.
9683295_oipm_En012_9645931.01-0620 __ 07-02-2020 . . . .
