Palmgren 9683122, Руководство по эксплуатации и список запасных частей

Страница: 2 / 24

2
Palmgren Operating Manual & Parts List 9683122 & 9683123
GETTING STARTED
STRUCTURAL REQUIREMENTS
Make sure all supporting structures and load attaching devices are
strong enough to hold your intended loads. If in doubt, consult a
qualified structural engineer.
ELECTRICAL REQUIREMENTS
The power supply to Model 9683122 needs to be 220 volt/ 9.7 amp,
three phase, 60 Hz. The standard allowable voltage variation is plus
or minus 10%.
The power supply to Model 9683123 needs to be 440 volt/ 4.9 amp,
three phase, 60 Hz. The standard allowable voltage variation is plus
or minus 10%.
TOOLS NEEDED:
Standard mechanic’s hand tool set.
UNPACKING
Carton should be handled with care to avoid damage from drop-
ping, bumping, etc. Store and unpack carton with correct side up.
After unpacking Band Saw, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing or dam-
aged parts. If any damage or loss has occurred, claim must be filed
with carrier immediately. Check for completeness. Immediately re-
port missing parts to dealer.
IMPORTANT: Table is coated with a protectant. To ensure proper fit
and operation, remove coating. Coating is easily removed with mild
solvents, such as mineral spirits, and a soft cloth. Avoid getting solu-
tion on paint or any of the rubber or plastic parts. Solvents may de-
teriorate these finishes. Use soap and water on paint, plastic or
rubber components. After cleaning, cover all exposed metal surfaces
with a light coating of oil. Paste wax is recommended for table top.
Band Saw is shipped partially assembled. End user will need to as-
semble loose parts to machine.
After unpacking the unit, carefully inspect for any damage that may
have occurred during transit. Check for loose, missing or damaged
parts. Shipping damage claims must be filed with the carrier.
All tools should be visually inspected before use, in addition to regu-
lar periodic maintenance inspections.
Be sure that the voltage labeled on the unit matches your power
supply.
UNPACK:
Do not discard packing materials until after machine has been in-
spected for damage and completeness. Locate loose parts and set
aside.
INSPECT:
After unpacking the unit, carefully inspect for any damage that may
have occurred during transit. Check for loose, missing or damaged
parts. Shipping damage claims must be filed with the carrier.
All tools should be visually inspected before use, in addition to regu-
lar periodic maintenance inspections.
Be sure that the voltage labeled on the unit matches your power
supply.
SPECIFICATIONS
9683122 9683123
Blade Length 167.75" - 169" 167.75" - 169"
Blade Width 1/4" - 3/4" 1/4" - 3/4"
Blade Thickness .035" .035"
HP 3 HP 3 HP
Voltage 220V 440V
Amperage 9.7 A 4.9 A
Phase 3 PH 3 PH
Cutting Capacity Rectangle 14" x 22" 14" x 22"
Cutting Capacity Round 14" 14"
Cutting Capacity Square 13-1/2" 13-1/2"
Table Height 36.5" 36.5"
Table Tilt 45° right; 15° left 45° right; 15° left
Blade to Frame 13-3/4" 13-3/4"
Electric Welder 4.2 kVA 4.2 kVA
Grinder Motor 1/8 HP 1/8 HP
Machine Dimensions 53" x 40" x 77.5" 53" x 40" x 77.5"
Weight 1500 lbs 1500 lbs
Speeds 0 - 1650 sfpm 0-1650 sfpm
Table Dimensions 24.25" x 24.25" 24.25" x 24.25"
Blade Wheels Diameter 24" 24"
SAFETY RULES
WARNING:
For your own safety, read operating instructions
manual before operating tool.
PROPOSITION 65 WARNING:
Some dust created by using
power tools contain chemicals known to the state of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•
Lead from lead-based paints
•
Crystalline silica from bricks and cement and other masonry
products.
•
Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals;
work in a well ventilated area and work with approved safety equip-
ment. Always wear
OSHA/NIOSH approved, properly fitting face
mask or respirator when using such tools
WARNING
: Always follow proper operating procedures as defined
in this manual even if you are familiar with the use of this or similar
tools. Remember that being careless for even a fraction of a second
can result in severe personal injury.
BE PREPARED FOR JOB
•
Wear proper apparel. Do not wear loose clothing, gloves, neck-
ties, rings, bracelets or other jewelry which may get caught in
moving parts of machine.
•
Wear protective hair covering to contain long hair.
•
Wear safety shoes with non-slip soles.
•
Wear safety glasses complying with United States ANSI Z87.1.
Everyday glasses have only impact resistant lenses. They are NOT
safety glasses.
•
Wear face mask or dust mask if operation is dusty.
•
Be alert and think clearly. Never operate power tools when tired,
intoxicated or when taking medications that cause drowsiness.