4
ASSEMBLY (CONTINUED)
STAND ASSEMBLY
Parts to be assembled should be located and accounted for (See
List and Figure 2).
IMPORTANT: Do not attempt assembly if parts are missing. Use this
manual to order repair parts.
A Base, 1 each
B 10-1.5mm Hex nut, 5 each
C 10-1.5 x 30mm Socket head bolt, 5 each
D Column, 1 each
E Water pot holder, 1 each
F Water pot, 1 each
G Top, 1 each
•
Slide column (D) into base (A); secure by tightening hex head
bolts (C) against column. Tighten hex nuts (B) against base to
secure bolts.
•
Slide water pot holder (E) over column. Tighten hex head bolt
(C) and nut (B) to secure holder.
•
Slide top (G) over column and secure with bolts (C) and nuts
(B).
•
Slide water pot (F) into holder. Adjust pot holder height as
required.
•
Secure base to floor for maximum stability and safety.
(Hardware not included.)
MOUNT GRINDER
Locate bag with following hardware:
8-1.25 x 45mm Hex head bolt, 4 each
8mm Flat washer, 8 each
8mm Lock washer, 4 each
8-1.25mm Hex nut, 4 each
•
Place grinder on top of stand.
•
Align mounting holes in grinder’s base with diagonal slots on
stand’s top.
•
Use 8-1.25 x 45mm hex head bolts with 8mm flat washers,
8mm lock washers and 8-1.25mm hex nuts to secure grinder to
stand top.
INSTALLATION
MOUNT GRINDER
•
Mount grinder to a solid horizontal surface (hardware not pro-
vided). If mounted to metal pedestal, align mounting holes
with corresponding holes in pedestal. Insert a
1
/
4
-20 x 1¼” hex
head bolt with flat washer through base of grinder. From bot-
tom of pedestal, place a
1
/
4
” flat washer and
1
/
4
”-20 hex nut onto
the bolt. Tighten only until space between grinder base and
pedestal is
1
/
8
” (base should be flush for 82101B). Using second
nut on each bolt, jam tighten against the first to prevent loos-
ening by vibration.
•
To mount grinder to wooden bench top, use
1
/
4
x 1¼” wood
screws with flat washers beneath heads. Tighten screws until
space between grinder base and bench top is
1
/
8
” (base should
be flush for 82101B).
GROUNDING INSTRUCTIONS
WARNING:
Improper connection of equipment grounding con-
ductor can result in the risk of electrical shock. Equipment should
be grounded while in use to protect operator from electrical shock.
•
Check with a qualified electrician if grounding instructions are
not understood or if in doubt as to whether the tool is properly
grounded.
•
This grinder is equipped with an approved 3-conductor cord
rated at 300V.
•
Do not remove or alter grounding prong in any manner. In the
event of a malfunction or breakdown, grounding provides a
path of least resistance for electrical shock.
WARNING:
Do not permit fingers to touch the terminals of plug
when installing or removing from outlet.
•
Plug must be plugged into matching outlet that is properly
installed and grounded in accordance with all local codes and
ordinances. Do not modify plug provided. If it will not fit in out-
let, have proper outlet installed by a qualified electrician.
•
Inspect tool cords periodically, and, if damaged, have repaired
by an authorized service facility.
•
Green (or green and yellow) conductor in cord is the grounding
wire. If repair or replacement of the electric cord or plug is nec-
essary, do not connect the green (or green and yellow) wire to
a live terminal.
•
The Palmgren 12” grinder is prewired for 240 volts, 60 Hz and
single-phase power. A qualified electrician should wire a 240
volt, 20 AMP, 3-prong plug to grinder line cord.
WARNING:
This work should be performed by a qualified
electrician.
EXTENSION CORDS
•
The use of any extension cord will cause some drop in voltage
and loss of power.
•
Wires of the extension cord must be of sufficient size to carry
the current and maintain adequate voltage.
•
Running the unit on voltages which are not within ±10% of the
specified voltage may cause overheating and motor burn-out.
•
Use the table to determine the minimum wire size (A.W.G.)
extension cord.
•
Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool plug.
•
If the extension cord is worn, cut or damaged in any way,
replace it immediately.
Palmgren Operating Manual & Parts List
82121
Figure 2 – Stand Assembly
F
G
B
C
E
B
C
D
A
B
C
