background image

9

Re-Load Instructions RevD

Toll Free: 800-788-1028  •

  

www.NomadFlexibleFurniture.com

6. Discharging of battery

6.1   As mobile devices get “Reloaded” from the charging hub, the battery will begin to 
slowly discharge.
6.2   When the BLUE LED is lit, this means the internal battery power status is in the range 
from 100% to 10%.
6.3   When the RED LED is lit the battery power status is below 10% and needs to be 
charged.  (The Re-Load hub will continue to “Reload” while LED is RED).
6.4   When there is NO colored LED lit, this means the circuit has shut-off and the internal 
battery needs immediate charging of the battery.  The Re-Load hub will not charge devices in 
this status.
6.5   Please refer to above instructions for charging battery during use, instruction 4.9.

NOTE: 

 While NO colored LED’s are lit, the battery retains a minimal power level.  This 

protects the battery from a deep discharge.  Batteries that go into a deep discharge state 
have a shortened life cycle.  A safe battery shut-off is integrated into the circuitry of Re-
Load.   This allows the Re-Load battery a longer and safer life cycle.  Under normal working 
conditions and proper maintenance, the battery should last 3+ years.

7. Removing internal battery

Over duration of using the ReLoad table it might be necessary to remove the internal battery. 
Please follow below instructions for easy removal.

7.1   Gain access to the battery compartment by unlocking the handle with the key provided. 
(Figure A, page 4, #08)
7.2   Pull back on the handle to release worksurface and tilt vertical.
7.3   Locate internal battery in the compartment.
7.4   Make sure all wire connections have been released from each other.
7.5   Locate Velcro strap and loosen the strap.
7.6   Locate vinyl strap on battery, slide hand between strap and battery pull upward.  Use 
your other hand to lift battery and get firm hold on it.  Battery weighs 13 lbs. so please DO 
NOT DROP.
7.7   To place battery back into compartment, make sure Velcro strap is flipped back on each 
side so the battery fits between.
7.8   Make sure all wires and wire connections are not under battery.
7.9   Tighten Velcro strap to hold battery back in place.

PLEASE RECYCLE OLD BATTERIES BY CONTACTING 1-800-BATTERY FOR LOCAL DROP-
OFF LOCATIONS OR PICKUP SERVICES.

Содержание Nomad Re-Load Mobile Table with Charging...















Отзывы: