background image

www.pall.com/biotech

5

1.4

Locating Safety Information

This care and use guide presents safety information as follows:

HELPFUL INFORMATION! 

Communicates important and helpful information about the current topic.

CAUTION!

Identifies safety risks that could cause personal injury, or situations that may cause 
product damage.

WARNING!

Identifies safety risks that can cause serious personal injury, or situations that may cause
irreversible damage to equipment. 

1.5

Environmental Compliance

Users should dispose of storage and by-product solutions according to local, state, and 
federal regulations. 

1.6

Where to Get Help

If you do not understand the information in this guide, or need additional assistance in using
Cadence ILC modules, contact Pall. Pall provides these additional resources to help make your
experience with our products trouble-free:

Materials Safety Data Sheets

— Offer safety information about the chemicals used to store

Cadence ILC modules, and are available online at 

www.pall.com/procedures

Support Services

— The Pall Biotech customer support team can answer technical questions

and provide replacement parts. 

Pall operates a technical service to assist in the application of our products. This service is
readily available to you and welcome your questions so that we can help. In addition, an
extensive network of technical representatives is available throughout the world. For additional
questions or technical assistance, you may contact 

[email protected]

.

Web Site (http://www.pall.com/biotech) 

— Provides contact information for Pall Biotech

offices throughout the world.

Содержание Cadence ILC



















Отзывы: