background image

 

22   

POWER PACK WIRING 

The external (2-button) switch, the 
internal (3-button) switch and the 
isolation switch is wired directly to the 
terminal strip on the power pack.  (See 
wiring diagram page.) 

FILL SYSTEM WITH HYDRAULIC OIL 

With the platform at ground level, remove 
the filler cap from the power pack. 

Pour in the oil from the container 
supplied, or use squeezable plastic bottle 
and pipe, until the level is up to the level 
line on the dipstick or up to the bottom of 
the fill hole on end fill tanks. Refit the 
filler/breather. 

Test Operating Cycle

 

 

Filler Cap/ Dipstick 
(End Filler Cap has no Dipstick) 

 

Do not load the platform in any way during these tests, as at this stage the lift is 

only tacked /clamped on. 

Lower open platform to ground then raise it to floor level, checking that lift operates freely 
and reaches both ground and floor level. 

Close the platform at a convenient height and then stow against stops. 

 

 

LUBRICATE CHAINS 

Thoroughly lubricate chains over full length.  It is important that this is done 

AFTER

 finish painting. 

 

 

 

 

 

 

 

Содержание V 1000 LQ



































Отзывы: