Palfinger ILU 40 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 35

background image

4 Installation Dimensions

Revision 1.5

- 9 -

Installation Dimensions

4

- Installation Dimension sheets are

supplied with each individual ILU

, as there are too many different

setup combinations for a generic installation drawing. When ordered a liftgate, PALFINGER Liftgates

supplies a drawing based upon the Chassis dimension sheet (Figure 1 and Figure 2) supplied by your

company.

IMPORTANT:

Before starting the installation, make sure that you have your own reference sheet that was supplied to

PALFINGER Liftgates together with the installation lay-out drawing. Compare it with the truck you are about

to start the installation on. If the

units are different

than the supplied lay-out, contact your supervisor and

PALFINGER Liftgates to go over the differences.

Do not start installation if your truck/trailer does not match up with PALFINGER Liftgates supplied

drawing!

Figure 3 Installation Drawing - provided by PALFINGER Liftgates engineering department

«
...
7
8
9
10
11
...
»

Содержание ILU 40




































Отзывы:

Нет отзывов

Похожие инструкции для ILU 40

Бренд: R. Beck Maschinenbau Страницы: 35

Бренд: OMA Страницы: 53

Бренд: GATmatic Страницы: 16

MCS 5500 ND WIRELESS

Бренд: Nussbaum Страницы: 57

Бренд: Grundfos Страницы: 23

BLUEBOX ADVANT UHF

Бренд: iDTRONIC Страницы: 54

Бренд: B&B Molders Страницы: 18

AXE 320 PULSE smart

Бренд: Alfain Страницы: 13

Бренд: DOLD Страницы: 20

I/O SYSTEM 750 750-635

Бренд: WAGO Страницы: 18

Бренд: Measurement Computing Страницы: 6

Бренд: ICP DAS USA Страницы: 8

Бренд: Avalon Страницы: 86

Бренд: OMCN Страницы: 8

Бренд: Lincoln Electric Страницы: 4

Kontrol-Karrier 185A

Бренд: morse Страницы: 6

Бренд: IFM Страницы: 16

Бренд: FACAL Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды