manualshive.com logo in svg

Paia 9720, Инструкция по сборке и использованию

Поделиться
Скачать
Paia 9720 Скачать руководство пользователя страница 13

9720 VCO      13

010321

Now we’ll continue wiring of the front panel parts as shown in fig 3. First,
notice that individual solder lugs are identified by part number and lug number.
For example, R200-1 means the lug labeled “1” of the Potentiometer R200.

Also, this convention will be followed in these steps: Do not solder a connec-
tion to a lug until told to do so with an instruction such as (s2), which means
that at that point there will be two wires on the lug in question.  If there are not
the number of wires specified at the lug when you get ready to solder, recheck
to see what has gone wrong.  Connections which should not be soldered yet
will be marked (ns) for NO SOLDER. On these unsoldered connections simply
push the end of the wire through the lug and crimp it back to mechanically
secure it.

(  ) Connect the free end of the solid wire extending beyond J11-S to

R203-1 (ns).

(  ) Cut a 3-3/4" length of bare wire and pass it through the holes

in the "S" lugs of J1 and J9. DO NOT SOLDER these two
connections. Bend the  "S" lugs of J2-J8 up to meet the wire
and solder these seven connections.

In the following steps cut a piece of bare wire to the length indicated and
use it to connect the component lugs specified. Route the wires as shown
in Fig 3 and push them down close to the front panel so they will not short
against the lugs of switches and jacks and future wiring. The "clipping"
length means that a resistor or capacitor lead clipped earlier should be used.

LENGTH

FROM

TO

(  ) clipping

R201-2 (s1)

R201-3 (ns)

(  ) clipping

R200-2 (s1)

R200-3 (ns)

(  ) clipping

R205-2 (s1)

R205-3 (ns)

(  ) 3-1/4"

S2-1 (s1)

R204-1 (ns)

(  ) 2"

R204-1 (ns)

R202-1 (ns)

(  ) 3/4"

R206-1 (ns)

J10-S (ns)

(  ) 3/4"

J7-X (ns)

S1-2 (ns)

Many point-to-point panel connections are made using the

Содержание 9720





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды