Pahlen Jet Swim 2000, Руководство пользователя, Страница: 6 / 20

6
Jet Swim 2000
MA30-02E
ENGLISH
Air
_
+
Flow
+
_
On/Off
Jet Swim 200 (Front panel)
M10199-2
130507 OA
A
B
C
Figure 1.
Front Jet Swim 2000
Flow
On/Off Air
Installation - Liner pool
1. Remove the stainless steel front and cut out the pool wall according to the hole pattern. The centre of the Jet Swim housing
shall rest 170 mm under the surface of the water.
2. Install the Jet Swim housing in the wall of the pool. Then attach the self-fastening washer on the bronze part.
3. Put the pool liner in place. Make sure that the two protruding Jet outlets do not damage / get caught on the pool liner.
Fill the pool with water. When the water reaches about 5 cm below the Jet Swim housing, the flange and rubber washer are
screwed in place against it.
Cut away the pool liner from the inside of the flange and then connect the starting hose to the switch and install the stainless
steel front.
4. Connect the hose for the air admixture and tighten the hose clamp. Then attach the outlet onto the hose 100 mm above the
surface of the water behind the pool wall.
5. Connect the starting hose to the pump’s contactor panel.
N.B.! The starting hose must be set in a loop 150-200 mm above the surface of the water.
6. Connect the pipes and valves to the pump according to the image (page 2). The threads are sealed with thread seal tape.
7. The electrical connection must be made by an
authorised electrician and be equipped with a residual current device.
8. Make sure that the pump’s direction of rotations is consistent with that of the system. Open the valves. Completely fill the
pump with water before starting it with the push-button( A fig.1) on the stainless steel front.
9. The flow can be controlled with the knob (B fig. 1) above the outlet nozzles. Air can be added to the water streams using the
knob (C fig. 1) below the outlet nozzles.
Installation - Concrete pool
1. Remove the stainless steel front and install the Jet Swim housing in the form. The finished pool wall shall be in line with the
flange on the bronze housing. The centre of the Jet Swim housing shall be located 170 mm under the surface of the water.
2. Install the leak flange for suction and pressure connections as well as the leak flange for the air admixture and starting hose
(protective pipe), prior to casting. The threads are sealed with thread seal tape.
3. After the casting (and any tiling) the stainless steel front is installed. The starting hose to the switch is installed before the
stainless steel front.
4. Connect the hose for the air admixture and tighten the hose clamp. Then attach the outlet onto the hose 100 mm above the
surface of the water behind the pool wall.
5. Connect the starting hose to the pump’s contactor panel.
N.B.! The starting hose must be set in a loop 150-200 mm above the surface of the water.
6. Connect the pipes and valves to the pump according to the image (page 2). The threads are sealed with thread seal tape.
7. The electrical connection must be made by an
authorised electrician and be equipped with a residual current device.
8. Make sure that the pump’s direction of rotations is consistent with that of the system. Open the valves. Completely fill the
pump with water before starting it with the push-button( A fig.1) on the stainless steel front.
9. The flow can be controlled with the knob (B fig. 1 ) above the outlet nozzles.
Air can be added to the water streams using the knob (C fig. 1) below the outlet nozzles.
Installation - Concrete pool with liner
Install according to point 1 - 2 for concrete pools and point 3 - 8 for liner pools.
Start
The pump must be filled with water prior to starting. Never run the pump dry ,
as that can damage the parts inside. Make sure that all the valves to and from the
pump are open prior to starting.
The Jet Swim pump is started and stopped by air impulse via the pushbutton (A)
on the stainless steel front; see figure 1.
The flow of water can be controlled using the knob (B) above the outlet nozzle;
see figure 1.
Air can be added to the water streams using the knob (C) below the outlet nozzles;
see figure 1.
Please note
Upon risk of freezing: close the valves, remove and drain the pump of all water.
Lower the water level to approximately 10 cm under the Jet Swim housing in order
to avoid freezing damage.
The pump should be store indoors in the winter.
When restarting: Check the condition of the starting button and the hoses.