PADAUK PDK5S-P-003 Скачать руководство пользователя страница 24

Страница: 24 / 27

PDK 5S-P-003

Program Writer

Page 24 of 27

PDK-5S-P-003-UM-EN-V006 – Oct. 30, 2018

(5) Or click on

『

Cancel

』

(6) Enter package setting. Please refer to section 5.6 to get relative descriptions. Click on

『

』

after complete

setting.

(7) Automatically download the configuration file to the Writer.

After complete the above steps, users can cooperate with semi-automatic equipment just do chips’ O/S tests or

blank checks.

NOTICE: Blank Check including O/S test.

8. Writer LCM Information and Buzzer Sound Table



Writer LCM information:

LCM information

Descriptions

Exclusions and Solutions

Wait : Load File

.PDK file was not loaded

Load .PDK file after connect to USB

IC ready.

IC is prepared

remove.

IC has been removed

IC O/S test fail

xP? O/S: Px Hi

xP? O/S: Px Lo

xP? O/S: G



xP? O/S: Px



xP? O/S: Px



IC open/short test failed

Please replace IC or

remove and put it again or

check Jumper , Connecting Board

and Settings again.

Do Check...

Do Erase..

Do Program...

Do Verify...

Do Adjust IHRC..

Do Protect...

IC is being checked

IC is being erased (MTP

only)

IC is being written

IC is being verified

IC is being adjusted

IC is being protected

<<< IC O.K. >>>

Writing completed

Not the IC.

IC type and .PDK file do not

match

Please replace the IC

IC not matched.

IC’s content does not match

Please replace the IC

IC not work(xx)

Writing failed and cannot

work

Please replace the IC

IC verify fail.

IC verified failed.

Please replace the IC

Over program cnt

Over write count

Please replace the IC

Содержание PDK5S-P-003




























Результаты поиска

Содержание PDK5S-P-003

Отзывы:

Похожие инструкции для PDK5S-P-003

Бренды по названию

Популярные бренды

PADAUK PDK5S-P-003, Руководство пользователя

Результаты поиска

Содержание PDK5S-P-003

Отзывы:

Похожие инструкции для PDK5S-P-003

Бренды по названию

Популярные бренды