CAUTION:
PLEASE FOLLOW THIS INSTRUCTION MANUAL CAREFULLY TO
PREVENT ANY INJURIES OR COMPLICATIONS THAT MAY ARISE.
WARNING:
Before installing or maintaining the luminary, make sure all powers are
TURNED OFF
.
Verify that supply voltage is correct by comparing it with the label information on all
fixtures.
Make all connections in accordance with the NEC requirements, and make sure all
luminaries are properly secured to prevent any wire complications. This luminary is
to always be installed with the lens facing down and its not to exceed the maximum
ambient temperature rating noted on the specification sheet.
Need help? Tech help line:
(800) 988-6386
Email:
Website:
www.paclights.com
Copyright © 2017 PacLights
All Rights Reserved
LED DRIVER
V(-)
[BLACK]
V(+)
[RED]
TO LOAD
[LED BOARD]
[WHITE]
[BLACK]
ACN [BLUE/WHITE]
ACL [BROWN/BLACK]
GROUND [GREEN]
NEUTRAL [WHITE]
GROUND [GREEN]
HOT [BLACK]
INPUT
OUTPUT
DIM
WHITE (-)
BL
UE(+)
Inside F2SB
PRE-CONNECTED
(DO NOT DISCONNECT)
Using a J-Box (not included), Connect the ACL and the ACN from the driver to the conduit with the AC Power Supply cords.Follow the Wiring Diagram provided.
* LED DRIVER Input Ground (green) wire only available for selected fixtures.
If the Ground Wire is missing and the Power Supply includes a ground wire, connect the power supply ground wire to the fixture.
(FOR DIMMABLE VERSION)
7. Using an allen wrench, remove the
two socket head machine screws in
order to access the LED driver inside
the fixture.
8. Using a slotted screw driver,
remove one of the conduit plugs from
a side of the luminaire in order to run
a flexible conduit with a power supply
cable inside it.
Note: Instructions are subject to change at any time without notice
5. Run the power cord from the
arm mount to the F2SB luminaire,
Once the cable has been inserted
inside the F2SB, connect the power
cable to the LED Driver inside the
F2SB. In order to access the LED
Driver cables, the electrician must
first remove the [6] screws from the
service door using a #2 Phillips
screw driver and make all
connections inside the luminaire.
6. Once all wiring is complete,
Close the service door and use
the M12 bolt to fasten the
Arm Mount to the F2SB.
Do not fasten completely.
02-00030-022618-2
FCPG Series LED Garage Light
Installation Sheet
Includes:
FCPG040, FCPG055, FCPG075, FCPG100
1. Using the provided screws, fasten the two
brackets to the top side of the FCPG fixture.
Use an allen wrench to tighten the screws to
a safe locking torch.
2. Mount the
U-Shaped bracket
to the ceiling
using mounting
screws (not
included). The
number and size
of the mounting
screws must be
determined by a
certified
personnel and
may vary
depending on
the mounting
surface.
INSTALLATION STEPS FOR SURFACE MOUNT
9. Run the flexible conduit through the opening on
the FCPG back box and lock it into the conduit
plug opening. Extend the power supply cables
inside the conduit to be connected to the LED
Driver inside the FCPG.
10. Use the wiring diagram provided to properly
connect the fixture to the power supply. All
connections must be compliant with NEC
standards and must be performed by a certified
electrician.
The FCPG fixture has two cables attached to it.
The First cable consists of 3 coductors: ACL (black),
ACN (white), and a ground (green). These conductors
are to be connected to a 120v AC Power Supply Cable.
The second cable consists of two conductors: Dim+
(purple) and a Dim- (gray). These cables are used if the
customer is installing a 0-10v dimmer to the FCPG
fixture. The dimmer is optional, please consult with a
Sales representative for more information.
3. Using the provided machine screws, carefully fasten the top
bracket to the two brackets attached to the FCPG by aligning
the holes and fastening to the desired height.
11. After all steps
are properly
followed, the
FCPG fixture is
ready to be
turned on. At this
point, provide
power to the
fixture.
AC-CPG-SB
Suspended Mount Bracket
