88820 LC
For indoor and outdoor use
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
a)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the product when in use.
m)This product is equipped with push-in type lamps. Do not twist lamps.
n) Read and follow all instructions that are on the product or provided with the product.
o)
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on
live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or
frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed, including tree, branches,
or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.
CAUTION:
1. Replace lamps only with
3.3 Volt, 20mA (0.066 Watt)
spare lamps provided with this product.
2. Risk of fire. This product does not contain lamp shunts, which allow the product to operate if
one lamp burns out. Replace lamps only with the spare lamps provided with this product.
USER SERVICING INSTRUCTIONS
Replace the lamp.
1. Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling cord.
2. Pull lamp and plastic base straight out of lampholder.
3. Replace lamp with only 3.3 Volt, 20mA (0.066 Watt),
LED type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step 3.
a) Remove the base of burned out lamp by straightening lamp leads and gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in each hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps in the
light set so that the leads will touch the contacts inside the lampholder.
CAN ICES-005(B) / NMB-005(B)
For questions and /or assistance, call customer service at 1-877-398-7337
or visit us on the web at www.geholidaylighting.com FP-18 PRINTED IN CHINA
© 2018 Nicolas Holiday Inc., 204 Spring Hill Road Trumbull, CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights reserved.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
If the product
does not light
One or more of the based LEDs may
have loosened from the socket during
transporting. There is a break in the
circuit between the LED leads and the
socket terminals. Male/female
connectors not fully inserted together.
Non working control box. Foot pedal
in off position.
Unplug the set at the outlet. Starting with the
first unlit LED, gently push (don't twist) each
LED base firmly into the socket. If still does not
light, then remove each based LED and check
for out of place lead wires. Make certain
connectors fully inserted and securing cap fully
tightened. Step on foot pedal to turn LEDs on.
If a based LED
is missing
One or more of the based bulbs may
have come out of the socket when
transporting.
Mark socket(s) with a piece of tape and unplug
the set. Replace the based LED or use one of
the spare based LEDs included with product.
If an LED fails to
light (shorts or
opens)
Incorrect LED, premature LED failure
or voltage is too high.
The LED may be out or dimly lit. Replace bad
LEDs as soon as you find them.
LEDs fail to
switch from
white to multi
Defective control box
Contact Customer Support.
