Packard Bell EasyNote SJ Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 28

Packard Bell EasyNote SJ Скачать руководство пользователя страница 3

Packard Bell EasyNote SJ Disassembly Manual

2

Overview

This document contains step-by-step disassembly instructions for the Packard Bell EasyNote
SJ. The instructions are illustrated where necessary with images of the part that is being
removed or disassembled.

Packard Bell reserves the right to make changes to the EasyNote SJ without notice.

Technician Notes

Only technicians authorized by Packard Bell B.V. should attempt to repair this equipment. All
troubleshooting and repair procedures are detailed to allow only subassembly/module level
repair. Because of the complexity of the individual boards and subassemblies, no one should
attempt to make repairs at the component level or to make modifications to any printed wiring
board. Improper repairs can create a safety hazard. Any indication of component replacement
or printed wiring board modifications may void any warranty or exchange allowances.

Disassembly

When disassembling the system unit, follow these general rules:

Turn off the power using the power button.
Disconnect the adapter.
Remove any SD/MMC card, ExpressCard or dummy card from the device.
Do not disassemble the system into parts that are smaller than those specified in the
instructions.
Label all removed connectors; note where the connector goes and in what position it
was installed.

Reassembly

Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and
screws are returned to their proper positions. Check that no tools or any loose parts have been
left inside the casing. Check that everything is properly installed and tightened.

Required Tools

All disassembly procedures can be performed using the following tools:

Small Phillips and flat-blade screwdriver.
Hex-bolt #5 screwdriver

«
1
2
3
4
5
...
»

Содержание EasyNote SJ





























Отзывы:

Нет отзывов