background image

 

 

03/2008 

Page 35 of 35 

PN 845671 

 

 
 

 

WARRANTY POLICY 

PACIFIC LIMITED WARRANTY

 

 

The 

Pacific

 Z20T has been manufactured, tested and inspected in accordance with specific 

engineering requirements.  This machine is WARRANTED to be free from defects in 
workmanship and materials for periods as follows from the date of purchase. 
 
Ten (10) Years Parts, One (1) Year Labor – Polyethylene Components 
Five (5) Years Parts, One (1) Year Labor – Main Frame 
Two (2) Years Parts, One (1) Year Labor – Brush Drive Motors 
One (1) Year Parts & Labor – All other components unless excluded below 
 
Travel time for warranty repair is authorized for a period of ninety (90) days following the date of 
sale to the end user, with a maximum of three (3) hours per claim. 
 
This warranty extends to the original user/purchaser and only when used, operated and 
maintained in accordance with 

Pacific

 Operating and Maintenance instructions. 

 
This warranty does not apply to certain wear parts and accessories of the machine such as 
electrical cords, carbon motor brushes, floor brushes, belts, hoses, tools, squeegee blades, etc., 
nor does it apply to damage or failure caused by improper use, abuse or neglect.  Warranty 
credit of return parts including motors, pumps, etc., is subject to incoming inspection of those 
items. 
 
To secure repair under this warranty, the following procedure should be taken: 

1. 

After the expiration of the ninety (90) day travel time warranty period, the customer is 

responsible for warranty travel payment for the inoperative machine or warranted parts must be 
delivered to the authorized dealer with shipping and delivery charges prepaid.  If unable to 
locate the Dealer, you may contact 

Pacific

 at the address listed herein for the location of the 

nearest 

Pacific

 repair center or agent or for other instructions pertaining to your warranty 

difficulty. 

2. 

Upon compliance with the above warranty procedure, all warranted repairs will be completed 

at no additional charge or cost to the user. 

3. 

Only 

Pacific

 or its authorized dealers and agents may make no charge warranty repairs on 

this product.  All others do so at their own risk. 
 
This warranty limits 

Pacific

 liability to the repair of the product and/or warranted parts 

replacement and does not include incidental or consequential damages arising from the use of a 

Pacific

 machine whether defective or not. 

 

BATTERY WARRANTY 

In addition to the terms above, any original equipment 

Pacific

 battery which becomes 

unserviceable under normal use within a period of ninety (90) days from the date of sale to the 
original user will be repaired or replaced with one of equal specification at our option, F.O.B. any 
authorized 

Pacific

 sales or service branch, with no charge to user, except transportation costs.  

After the expiration of the above ninety (90) day period, any battery which fails under normal 
use will be adjusted to the original user with a new battery of equal specification on a twelve 
(12) month pro rata basis from the date of purchase.  Adjustments will be determined using the 
then current list price, plus transportation costs.  Warranty is rendered null and void if battery is 
not kept filled to the proper level with DISTILLED WATER. 
 
This warranty is in lieu of all other expressed or implied warranties and is extended to the 
original purchaser/user.

 

Содержание Z20T




































Отзывы: