Pacific energy SUPER 27 Скачать руководство пользователя

Страница: 9 / 24

300913-24

SUPER-SD1 9

Residential
Installation

Warning:

Under no circumstances is this heater to be

installed in a makeshift or "temporary" manner. It may be
fi red only after the following conditions have been met.

* DO NOT ATTEMPT TO CONNECT THIS HEATER

TO ANY AIR DISTRIBUTION DUCT.

* The services of competent installer are strongly rec-

ommended.

* Outside combustion air or fresh air into the room may

be required in your area, consult local building codes
(see Combustion Air section).

- The services of a competent or certifi ed installer, (certifi ed
by the Wood Energy Technical Training program (WETT)
- in Canada, Hearth Education Foundation (HEARTH) - in
U.S.A.,) are strongly recommended.

BOTH CHIMNEY SYSTEM AND CONNECTOR MUST
BE LISTED TO: IN CANADA - ULC S-641 LISTED CON-

IN CANADA - ULC S-641 LISTED CON-

NECTOR AND ULC-S-629 LISTED CHIMNEY,

IN USA

- UL-103 HT LISTED CONNECTOR AND CHIMNEY

Clearances

1. This heater may be installed using a single-wall con-

nector (smoke pipe) or listed double-wall connector
(see Mobile Home installation).

2. Clearances to combustible surfaces and materials

using single-wall connector are shown in Figure #1,
page 6.

Clearances may be reduced with various heat insulat-
ing materials. Consult local fi re codes and authorities
for approval.

3. Alternately, for close clearances, use a listed double-

wall connector. See Diagram #1, page 6.

Chimney and Connector

Connect to a listed chimney or a chimney suitable for use
with solid fuel that is lined and in good condition and
meets local building codes. The chimney fl ue size should
be the same as the stove outlet for optimal performance.
Reducing or increasing the fl ue size may adversely affect
stove performance. Chimney fl ue exit is to be 3 feet (1 m.)
above roof and two feet (0.6 m.) above highest projection
within 10 feet (3 m.). The installation must meet all local
codes. Do not connect this unit to a chimney fl ue serving
another appliance. Minimum system height is 15 feet (4.6
m.) (measured from base of appliance).

Double-Wall Connector

Use a listed double-wall connector.

- Install all components to the chimney connector

manufacturer's installation requirements.

Single-Wall Connector

Smoke pipe must be:
* as short and straight as possible, use six inch diam-

eter, 24 gauge black pipe that is clean and in new
condition.

* secured at every joint and collar with 3 sheet metal

screws.

* installed with the crimped or male ends pointing down.

This will carry any liquid creosote or condensation
back into the stove.

* The chimney connector shall not pass through an attic,

roof space, closet or similar concealed space, fl oor,
or ceiling. Where passage through a wall, or partition
of combustible material is desired, the installation
shall conform to CAN/CSA-B365, Installation Code
for Solid-Fuel-Burning Appliances and Equipment.

Procedure

1. If a listed chimney and double-wall connector is to

be connected to the stove, install all components to
the chimney manufacturer's installation requirements.
(Outside combustion air may be required, consult
local building codes. See Combustion Air section.)

2. If it is desirable to use smoke pipe in conjunction with

the insulated chimney, see step 4.

3. If a roof or ceiling support is used in the installation,

you will fi nd the chimney manufacturer's complete
instructions packed with the roof support.

4. To start installing smoke pipe (chimney connector),

slip crimped edge of the pipe inside the stove collar.
Use holes provided in collar to secure pipe with two
screws.

5. Install the remaining lengths of pipe one on top of the

other to the fi nished height of the chimney connector
and secure to each other.