190617-24 AL6B
©PACIFIC ENERGY FIREPLACE
PRODUCTS LTD.
3
Safety and Maintenance
1. Burn only dry, well seasoned wood. The denser or heavier the wood when dry, the
greater its heat value. This is why hardwoods are generally preferred.
Green or wet
wood should not be used, as it will reduce heat output, as well as contributing
significantly to creosote buildup.
2. Remove ashes frequently and only when the stove is cold. Too much ash could cause
embers to roll out the door when it is opened. This may pose a fire hazard. For proper
operation, maintain a 1"(25mm) minimum ash base.
3. If glass becomes darkened from slow burning or poor wood, it can readily be cleaned with
fireplace glass cleaner when stove is cold. Never scrape with an object or use abrasive
cleaners that might scratch the glass. The type and amount of deposit on the glass is
a good indication of the flue pipe and chimney buildup. A light brown dusty deposit that
is easily wiped off usually indicates good combustion and dry, well-seasoned wood,
therefore relatively clean pipes and chimney. On the other hand, a black greasy deposit
that is difficult to remove is a result of wet and green wood and too slow a burning rate.
This will also create heavy deposit buildup in the chimney.
4. DOOR GASKETS - The gasket used by Pacific Energy (5/16"(8mm) medium density
fiberglass rope) requires only light pressure to seal. This will prolong seal life. It is
important that the door seal be maintained in good condition. Periodically inspect seals
and replace if necessary. Follow instructions included in the door gasket kit obtainable
from your nearest Pacific Energy dealer.
5. DOOR GLASS - Do not slam loading door or otherwise impact glass. When closing
door, make sure that no logs protrude to impact the glass. If the glass gets cracked
or broken,
it must be replaced before using the stove.
Replacement glass can be
obtained from your dealer. Use ceramic glass only.
Do not substitute with any other
type.
GLASS SIZE - 20.125”(511mm) x 11.875”(302mm) x 5mm
To remove broken glass, undo the four retaining screws and remove clamps, noting position
for re-assembly. Remove all particles of glass. Be careful as they are very sharp. Install
new glass complete with gasket. Replace clamps and screws.
6. Do not store wood within heater installation clearances, or within the space required
for fuel loading and ash removal. Keep the area around the heater clean and free of
loose combustibles, furniture, newspapers, etc.
7. If the heater requires cleaning, use mild soap and water only.
Use of abrasive cleaners
will void warranty.
8. Establish a routine for fuelling and firing the heater. Check daily for creosote buildup
until experience shows how often you need to clean the chimney to be safe.
9. Be aware that the hotter the fire, the less creosote is deposited. Weekly cleaning may
be necessary in mild weather, even though monthly cleaning is usually enough in the
coldest months when burning rates are higher.
10. Instruct all members of your family on the safe operation of the heater. Ensure they
have enough knowledge of the entire system if they are expected to operate it. Study
the section on chimney fires and the importance of following the steps outlined "In Case
of Chimney Fire".
WARNING:
Never use chemicals or any other volatile
liquid to start a fire. Do not burn garbage,
or flammable fluids such as gasoline,
naptha, or engine oil. We strongly
recommend that smoke detectors be
installed.
CAUTION:
• do not overtighten, tighten screws very
carefully
• do not clean glass when hot
• do not use abrasive cleaners on glass
WARNING:
Only use materials and components sup-
plied or specified by manufacturer when
doing maintenence or replacements.
NATIONAL
FIREPLACE
INSTITUTE
CERTIFIED
We recommend that
our woodburning hearth
products be installed and
serviced by professionals
who are certified in the
U.S. by the National
Fireplace Institute
®
(NFI)
as NFI woodburning
Specialists or who are
certified in Canada by
Wood Energy Technical
Training (WETT).
Wood Energy
Technical Training
