background image

Tools Needed

□ Temperature Controlled Soldering Station with small tip

   or 15-35 watt soldering iron with small tip.

□ Solder 60/40 or 63/37 Tin-Lead
□ Small Diagonal Cutters

□ Small Needle Nose Pliers
□ Pencil, Pen, and/or Highlighter

□ BRIGHT work light

Optional

□ Magnifying headpiece or lighted magnifying glass.

□ Multi-meter
□ Solder Sucker or Solder Wick

□ Knife or Wire Stripper
□ Cookie Sheet to build in and keep parts from jumping onto the floor.

Construction Techniques

□ Please take time to inventory the parts before starting.  Report any shortages to QRPKITS.com (In 

many cases it may be faster and cheaper to pull a replacement from your parts supply, but please 

let us know if we missed something.)

□ Pre-sorting the resistors and capacitors can speed up the assembly and reduce mistakes. 

□ There is no need to print out the whole assembly manual unless you want a copy.  Print the Parts 

List and Schematic (last two pages) then view the rest of the manual on a computer, laptop, or 

tablet.  The Parts List has columns for inventory and construction.

□ You can insert several parts at a time onto the board.  When you insert a part bend the leads over 

slightly to hold the part in place, then solder all at the same time.  Clip the leads flush.

□ Most parts should be mounted as close to the board as possible.  Transistors should be mounted 

about 1/8” above the board.  Solder one lead on ICs or IC sockets and then check to make sure the
component is flush before soldering the remaining leads.

□ Use a Temperature Controlled Soldering Station with small tip or 15-35 watt soldering iron with 

small tip.  Conical or very small screw driver tips are best.  

□ DO NOT use a large soldering iron or soldering gun.
□ If you are a beginner, new to soldering, there are a number of resources on the web to help you 

get on the right track soldering like a pro.  Google Soldering Techniques.  

Easy TR Switch 20170209   

                                      2        

Содержание Easy TR Switch










Отзывы: