PACH & COMPANY AeGIS 4000, Инструкция по установке и программированию

Страница: 18 / 37

01-20
INDIVIDUAL
ACCESS CODE
TO ACCESS
RELAY 1
(DOOR 1)
21-40
INDIVIDUAL
ACCESS CODE
TO ACCESS
RELAY 2
(DOOR 2)
41-50
INDIVIDUAL
ACCESS CODE
TO ACCESS
BOTH RELAY 1
AND 2 (DOOR 1
AND DOOR 2)
Step 3 Enter 00 then #, you will
hear “No Beep”.
Step 4 Enter new 4-digit Master
Code then press # then you will hear
“One Short Beep” and proceed to
step 5 or if you decided
not to change the existing Master
Code press
∗
to exit and you will hear
“Three Short Beeps”.
Step 5 Continue to program another
parameter or press
∗
to exit; you will
hear “Three Short Beeps” .
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release.
If you are in the pro-
gramming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear
“One Short Beep”. If you
entered an invalid master code you will
hear
“One Long Beep” , repeat
step 1. Should your master code
become lost or forgotten see section
Reset Master Code.
Step 3 Enter the Index Number
(01 – 20, 21-40 or 41-50) then #, you
will hear
“No Beep”. If the associated
Index Number has an access code
programmed, you will hear
“Two Long
Beeps”. Press
∗
, you will hear “One
Short Beep” and select another Index
Number.
Step 4 Enter the 4-digit access
code then #, you will hear “One
Beep”.
Do not program the same code as in
index01-20, 21-40 and 41-50, doing
so the access code programmed
won’t work.
Step 5 Return to step 3 to program
another access code or enter another
Function Code to program another
parameter, otherwise
press
∗
to exit and you will hear
“Three Short Beeps
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter the 01-20, 20-21 or
41-50) then press #, you will hear “No
Beep”: the index numbers is empty
and proceed to Step 5. “Two Long
Beeps”: the index number is not
empty and you must do one of the
following:
• Press 1 then # you will hear
“No
Beep” to overwrite existing access
code and proceed to Step 4.
• Press
∗ ∗
you will “One Short Beep”
and repeat this step.
Step 5 Enter the 4-digit access
code number then press #, you will
hear
“One Short Beep”.
Do not program the same code as in
index 01-20, 21-40 and 41-50, doing
so the access code programmed
won’t work.
Step 6 Return to step 4 to program
another access code or enter another
function code to program different
parameter or exit the
program by pressing
∗ ∗
and you will
hear “Three Short Beeps”.
Pach and Company Page 9
AeGIS 4000 Chapter 3. Programming
Step 1 Call to the AeGIS 4000 sys-
tem (you must know the system’s
phone number), you will hear:
“One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
•
“One Short Beep”, the master code
is accepted then press # and you will
hear
“One Short Beep” .
• “One Long Beep” , the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the pro-
gramming mode and you will hear
“One Short Beep” or
∗∗
to hang-up
the call.
Step 4 Enter the 01-20, 21-40, or
41-50then press #, you will hear “No
Beep”: the index numbers is empty
and proceed to Step 5. “Two Long
Beeps”: the index number is not
empty and you must do one of the
following:
• Press 1 then # you will hear
“No
Beep” to overwrite existing access
code and proceed to Step 4.
• Press
∗ ∗
you will “One Short Beep”
and repeat this step.
Step 5
Enter the 4-digit access
code number then press #, you will
hear
“One Short Beep”.
Do not program the same code as in
index 01-20, 21-40 and 41-50, doing
so the access code programmed
won’t work.
Step 6
Return to step 4 to program
another access code or enter another
function code to program different
parameter or exit the
program by pressing
∗ ∗
and you will
hear “Three Short Beeps” .
Function Local Programming Premise Phone Remote Phone
Program
Individual
Access Code