Pace XR 3000 Скачать руководство пользователя страница 3

Page 3 of 23

  

??

Adequate warning signs and symbols should be displayed in the vicinity of 
the XR 3000 warning of possible x-ray exposure.  Any warning lamps and 
signals should be checked prior to operating the XR 3000. 
 

??

The electrical circuits of the XR 3000, although enclosed for operator 
protection, must be considered as a potential hazard.  Strict observance of 
safety practices pertaining to operation and maintenance is essential.  
Proper electrical grounding must always be used. 
 

??

Before operating the XR 3000, all personnel designated or authorized to 
operate the unit, as well as those supervising its operation, should have a 
full understanding of how it works.  Additionally, they should be familiar 
with established radiation safety exposure practices sanctioned by the 
National Bureau of Standards Handbook, “X-ray Protection” HB93, 
pertaining to x-ray protection. 
 

??

Service personnel should read this manual and be familiar with its 
contents before attempting to adjust or repair this equipment. 

 
 

2. 

Radiation Safety Information 

 

Federal, State and Local Radiation Regulations (US ONLY) 

 

This cabinet x-ray system was designed to conform to U.S. and Food and 
Drug Administration (FDA) requirements as stated in the Code of Federal 
Regulations, Title 21 (21CFR).  These requirements (often referred to as the 
CDRH or BRH regulations) govern the design and manufacture of all 
equipment that produces ionizing radiation.  Such equipment includes 
television sets and microwave ovens, as well as cabinet x-ray systems.  In 
fact, the maximum allowable radiation emission for cabinet x-ray systems is 
the same as that set for television sets and microwave ovens.  Therefore, 
respect to radiation emission, a properly  maintained and operated cabinet x-
ray system is a safe as a television or microwave oven. 

Содержание XR 3000
























Отзывы: