background image

©2012 PACE Inc., Southern Pines North Carolina                All Rights Reserved 

    Page 20 of 20 

 

PACE LIMITED WARRANTY STATEMENT 

 

Limited Warranty

 

Seller warrants to the first user that products manufactured by it and supplied hereunder are free of 
defects in materials and workmanship for a period of one year (1) from the date of receipt by such user.  
This Warranty as applied to blowers and motor pumps is limited to a period of six (6) months.  Other 
brand equipment supplied but not manufactured by PACE are covered under their respective 
manufacturer’s warranty in lieu of this Warranty.   
This warranty does not cover wear and tear under normal use, repair or replacement required as a result 
of misuse, improper application, mishandling or improper storage.  Consumable items such as tips, 
heaters, filters, etc. which wear out under normal use are excluded.  Failure to perform recommended 
routine maintenance, alterations or repairs made other than in accordance with Seller’s directions, or 
removal or alteration of identification markings in any way will void this warranty. This warranty is 
available only to the first user, but the exclusions and limitations herein apply to all persons and entities. 
SELLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND MAKES NO WARRANTY OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 
Seller will, at its option, repair or replace any defective products at its facility or other location approved by 
it at no charge to user, or provide parts without charge for installation by the user in the field at user’s 
expense and risk.  User will be responsible for all costs of shipping equipment to Seller or other location 
for warranty service. 
EXCEPT FOR THE REMEDY ABOVE DESCRIBED, UNLESS OTHERWISE REQUIRED BY 
APPLICABLE LAW, SELLER WILL HAVE NO OTHER OBLIGATION WITH REGARD TO ANY BREACH 
OF WARRANTY OR OTHER CLAIM WITH RESPECT TO THE PRODUCTS, OR LIABILITY FOR ANY 
DIRECT, INDIRECT, CONSEQUENTIAL, OR INCIDENTAL LOSS OR DAMAGE CAUSED BY OR 
OCCURRING IN CONNECTION WITH ANY OF THE PRODUCTS. 
Warranty service may be obtained by contacting the appropriate PACE Company or local Authorized 
PACE distributor as set forth below to determine if return of any item is required, or if repairs can be made 
by the user in the field.  Any warranty or other claim with respect to the products must be made with 
sufficient evidence of purchase and date of receipt, otherwise user’s rights under this warranty shall be 
deemed waived. 
 

 
 
 
 
 
 

 

 

 
 
 
 

 

www.paceworldwide.com

  

PACE Incorporated

 

 

Pace Europe

 

255 Air Tool Drive 

 

11 Holdom Avenue 

Southern Pines,  

 

Bletchley, Milton Keynes, 

North Carolina, 28387   

United Kingdom, MK1 1QU 

Tel:  (877) 882-PACE   

Tel:  011 44 1908 277666 

Tel:  (910) 695-7223 

 

Fax: 011 44 1908 277777 

Fax: (910) 695-1594 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание IntelliHeat ST 115





















Отзывы: