manualshive.com logo in svg

Pace Edwards UltraGroove Electric KE2003, Руководство по установке

Поделиться
Скачать
Pace Edwards UltraGroove Electric KE2003 Скачать руководство пользователя страница 9

 

8  

Locate  the  sweep  seals  (rubber  weather  strips)  on  the  rails. 
Open the provided 303 brand protectant sponge pack that you 
removed  from  the  Topcover  in  step  5  (find  it  adhered  to  the 
underside of the top cover).  Wipe the underside of the sweep 
seal and the top of the wear strip. 

Extend  the  cover  to  the  tailgate.  Use  an  Allen  wrench  if 
needed  to  carefully  draw  out  the  sweep  seal  (seal  should  be 
angled  outwards  toward  the  cover  –  not  rolled  in  toward  the 
bed rail).

 (Fig. 9A) 

 

Proper care and  placement of the sweep seal  will  ensure the 
smooth  operation  of  the  cover.  Alcohol,  petroleum  based  or 
silicon-based  UV  Protectants  such  as  Armor-All®  should  be 
avoided and ARE NOT recommended for our covers.  

 STEP 9:   LUBRICATING & PLACING THE SWEEP SEALS 

FIG. 9A 

 STEP 8:   INSTALLING TAILGATE DRAINTUBES 

To install the tailgate drain tubes you need to find suitable holes in the 
rear stiffener of you truck bed. Figure 8C shows possible hole 
locations. 

Next you will screw the drain tube into the drain fitting and slide it on 
the tailgate cap as shown in Figure 8B. There is an interference bump 
on the cap that will lock the drain fitting in place. Next you will need to 
thread the drain tube in the desired hole and trim the length of the 
tube if needed. If there are no holes on the tailgate side of your truck 
you will need to drill holes, make sure to check for wires you could 
damage first (5/8” or 16mm). 

WARNING: Drain tube installation is paramount to getting the 
best possible water resistance out of your cover!  

FIG. 8A 

FIG. 8B 

Tailgate Drain 
Fitting 

Tailgate Drain 
Tube 

Tailgate Cap 

 

TAILGATE DRAIN 

TUBES X 2 

DRAIN FITTINGS     

X 2 

Possible Hole 
Locations 

FIG. 8C 

 STEP 10:   CONNECTING THE ELECTRONICS 

The electronics box has been pre-mounted to the inside of the canister.  

Connect the battery wire harness into the  2-wire plug at the end of the canister (

also  connect  the 

optional manual switch harness, if installed at this time

)  

Attach  the  Red  (positive)  and  Black  (negative)  wires  to  the  battery  or  the  truck  manufacturers 
suggested connection points at this time. 

Unit is now ready to operate.  
Press the Open button to open cover and press the Close button to shut the cover.  

2-BUTTON REMOTE 

KEY FOB x 2 

HARDWARE 

USED: 

RIBBED BLANKET 

SWEAP SEAL 

RAIL 

SOLID WEAR STRIP 

Содержание UltraGroove Electric KE2003













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды