background image

31

BRAKE CLUTCH SERVICE

DISASSEMBLY

1.   Remove the snap ring and sprag bushing retainer from 

one end only.

2.   Pull the inner race out.  Examine the race for scoring, 

wear or indentations caused by the sprag cams.  If the 
inner race is not completely smooth, the entire brake 
clutch assembly must be replaced.

3.  Use a screwdriver and mallet to remove the sprag 

bushing from one end of the outer race. There are four 
special cut-outs in the bushing for this purpose.  Be 
careful not to damage the bushing inside surface.  If 
a bushing’s inside surface is damaged or shows wear, 
replace it..

4.  Next, slide the sprag clutch out, inspect the sprag 

clutch closely for abnormal wear, cracks, pitting or cor-
rosion.  Check small clips for breakage or bright spots; 
the signs of excessive wear.  Unless the outer race 
or remaining sprag bushing is damaged or shows ex-
cessive wear, there is no need for further disassembly.  
If disassembly is necessary, remove the bushing ac-
cording to the procedure covered in Step No. three (3).  
All brake clutch assembly parts should be thoroughly 
cleaned and inspected before assembly.

ASSEMBLY

1.  Press a sprag bushing into the outer race, using a 

mechanical or hydraulic press.  A fl at plate of approxi-
mately the same diameter as the bushing fl ange  out-
side diameter should be placed between the press and 
bushing during assembly to protect the bushing.  Be 
certain the bushing fl ange is against the shoulder in 
the outer race.

The polished surfaces of the races and sprag cams 
must be perfectly smooth to insure positive engage-
ment of the clutch.  The slightest defect may reduce 
brake clutch effectiveness, which could result in prop-
erty damage, severe personal injury or death.  It is 
generally recommended to replace the entire brake 
clutch assembly if any component is defective.

CAUTION

WARNING

!

!

Содержание Braden BA2A




































Отзывы: