PAC HEIGH10 Скачать руководство пользователя страница 29

Страница: 29 / 38

Stinger HEIGH10

Radio Replacement Kit

2015-2021 Chrysler 300

2015-2021 Dodge Challenger / Charger

SRK-CHR15H

PAC-Audio.com

Pacific Accessory Corporation

Page 29

Rev: V3

Date: 032222

Section 4.1: Dodge Challenger/Charger Interface & Radio Module Mounting Preparation (cont.)

Part Two: Interface and Radio Module Mounting (cont.)

Step 5

Step 6

Route the other end of the display

cables through the opening in

the mounting assembly. Leave

approximately two inches of cable

extending out the front.

Position the radio module between

the side brackets and align the left

side mounting holes as shown.

Secure the radio module to the side

bracket using two M5x10 screws

from the HEIGH10 hardware.

Align the right side mounting holes

as shown. Secure the radio module

to the side bracket using two

M5x10 screws from the HEIGH10

hardware.

Step 1

Step 2

Step 3

From the SRK-CHR16-HAR, plug

in the HEIGH10 16-pin Main Radio

harness, 6-pin SWC/IR harness

and the 10-pin Multi Camera

harness.

Connect the Reverse Cam RCA

on the SRK-CHR16-HAR to

the Reverse Camera In on the

HEIGH10 24-pin AV harness.

From the HEIGH10 components,

plug the 24-pin AV harness into the

radio module.

Part Three: Radio Module Harness Connections

For Dodge Challenger/Charger proceed to Section 5 on Page 32

Содержание HEIGH10







































Результаты поиска

Содержание HEIGH10

Отзывы:

Похожие инструкции для HEIGH10

Бренды по названию

Популярные бренды

PAC HEIGH10, Руководство пользователя

Результаты поиска

Содержание HEIGH10

Отзывы:

Похожие инструкции для HEIGH10

Бренды по названию

Популярные бренды