PAC HEIGH10 Скачать руководство пользователя страница 1

Страница: 1 / 38

Stinger HEIGH10

Radio Replacement Kit

2015-2021 Chrysler 300

2015-2021 Dodge Challenger / Charger

SRK-CHR15H

PAC-Audio.com

Pacific Accessory Corporation

Page 1

Rev: V3

Date: 032222

Introduction and Features

Important Notes

Included Components

We recommend reading this manual thoroughly to familiarize yourself with

the entire process prior to beginning the installation.

1. Mounting Bucket 1 (CDJ13H-1)

2. Mounting Bucket 2 (CDJ13H-2)

3. Display Mounting Frame (CDJ13H)

4. CAN-Bus Connection Harness (MQS4PT36V2)

5. Mounting Hardware:

4- #8 X 1/2” PHP POINT TIP SCREWS

4 - #8 X 3/4” PHP POINT TIP SCREWS

1 - M4 X 8, FHP, BLACK DISPLAY SET SCREW

6. 6” Data Harness (10P-2-10P-6-HAR)

7. Main Wiring Harness (SRK-CHR16-HAR)

8. Side Brackets (CDJ13H-LH/RH)

9. Spacers (CDJ13H_Bracket Spacer) x2

10. Satellite Antenna Adapter (SAT-01)

11. AM/FM Antenna Adapter (BAA22)

12. PAC-LINK Interface Module (PL1)

13. RadioPRO Interface Module (CH4A-SRK)

14. Chime Speaker & Hardware (RPA-SPK)

15. Media Hub (USBHUB-CH1B-RCA-48)

16. Zip Ties (Not shown)

Does

Not Retain:

Cluster Display Features

• Compass (when equipped with 5” or 8.4” screen)

• Clock

• Phone pop-ups

• Navigation pop-ups

• Launch Control Timers

Factory Amplifier Features

• Speed Controlled Volume

• Surround Sound

Uconnect Features

• Uconnect Access Remote Start / Lock / Unlock

• SOS / Assist

• Vehicle Location Service

• WiFi-Hotspot

2. Not compatible with SRT or Hellcat trim levels.

3. Not compatible with 2015 model year vehicles equipped with drive modes.

4. Ensure that the CH4A-SRK and PL1 modules have been updated to the latest version of firmware before installing into

the vehicle. Refer to the Updating Firmware section at the end of the manual for firmware update instructions.

5. The vehicle should be OFF and key removed during entire disassembly and installation. Turning on the vehicle during

the installation may cause error codes / check engine light.

The SRK-CHR15H is a complete radio replacement kit for the installation of the Stinger HEIGH10® modular radio in Chrysler 300,

Dodge Challenger or Dodge Charger equipped with either 5” or 8.4” factory display radios. All modules, cables and adapters

are included to retain important features of the factory system, including: steering wheel-mounted radio controls, factory

amplifier, factory reverse camera, USB port and AM/FM reception. Plug & Play wiring harnesses allow for quick and easy

installation without the need to cut or splice any wiring. The display mounting panel allows mounting the 10-inch display

without modifying/cutting any part of the vehicle’s sub-dash.

NOTE: Along with the SRK-CHR15H components, additional

hardware and wire harnesses from the HEIGH10 (UN1810) kit

will also be used in the installation.

Performance Features

• Launch Control with Launch RPM

• Line Lock

• G-Force status on radio (still on instrument cluster)

SiriusXM Guardian Services

• SiriusXM Radio

Содержание HEIGH10







































Результаты поиска

Содержание HEIGH10

Отзывы:

Похожие инструкции для HEIGH10

Бренды по названию

Популярные бренды

PAC HEIGH10, Руководство пользователя

Результаты поиска

Содержание HEIGH10

Отзывы:

Похожие инструкции для HEIGH10

Бренды по названию

Популярные бренды