background image

Environmental Protection

1. 

Environmental protection should be a 

priority of considerable importance when 
using the machine, for the benefit of both 
social coexistence and the environment in 
which we live. Try not to cause any 
disturbance to the surrounding area.

2.

 You must comply with local regulations and 

provisions for the disposal of packaging, oils, 
petrol, filters, damaged parts or any elements 
which have a strong impact on the 
environment. This waste must not be 
disposed of as normal waste. It needs to be 
separated and taken to specified waste 
disposal centres where the material will be 
recycled.

3.

 You must comply with local regulations for 

the disposal of waste materials after mowing.

4. 

When disposing, do not pollute the 

environment with the machine, but hand it 
over to a disposal centre, in accordance with 
the local laws in force.

Recycling And Disposal

 

 

We do not offer a takeback  

 

 

scheme for the recovery of  

 

 

Waste Electrical Electronic 

 

 

Equipment (WEEE) & Batteries.  

 

 

Instead the responsibility to dis 

 

 

pose of WEEE and or 

 

 

Batteries is passed onto you by  

  us.

So when it becomes necessary to dispose of 
your machine you must take it to your local 
Civic Amenity Site. For further information 
please contact your local Authority for 
disposal advice.

You 

MUST

 make sure that all unused oil and 

fuel is disposed of correctly either beforehand

Maintenance & Care

We are a Member of the VALPAK 
National Compliance Scheme and our 
registration number is 

RM08660

For further information about disposal please 
contact your Local Authority.

You can also get more advice and guidance 
about recycling at the following website 
http://www.recycle-more.co.uk

Should you pass this product on to another 
user either sold or loaned, you 

MUST 

pass on 

this user manual. This will make sure that all 
other users can use and maintain this machine 
safely.

                  This symbol means you should 
 

       ‘Reduce - Reuse - Recycle’

or at your local Civic Amenity Site.

Under NO circumstances must any fuel or oil 
be put down any drains.

Certain products contain WEEE waste which
should not be disposed of in your domestic 
waste.

You 

MUST 

recycle WEEE in accordance with 

your local authority or recycling centre.

Certain products contain batteries which
should not be disposed of in your domestic 
waste.

You 

MUST

 recycle batteries in accordance 

with your local authority or recycling centre.

Unwanted packaging and materials should be 
stored and taken to a recycling centre so it 
can be disposed of in a manner which is 
compatible with the environment.

  43

Содержание P4600SP





















































Отзывы: