P.I.T. PWG125-C, Руководство пользователя

Страница: 7 / 28

Concrete Grinder
06
tools are dangerous in the hands of untrained
users.
► Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condition
that may aff ect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
► Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
► Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed.
Use
of the power tool for operations diff erent from
those intended could result in a hazardous
situation.
Service
► Have your power tool serviced by a
qualifi ed repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Safety information for the angle
grinder
Safety Warnings common for Grinding,
Sanding, Wire Brushing or Abrasive Cut-
ting Off operations
► This power tool is intended to function
as a grinder, sander, wire brush or cut-off
tool. Read all safety warnings, instruc-
tions, illustrations and specifi cations pro-
vided with this power tool.
Failure to follow
all instructions listed below may result in elec-
tric shock, fi re and/or serious injury.
► Operations such as polishing are not
recommended to be performed with this
power tool.
Operations for which the power
tool was not designed may create a hazard
and cause personal injury.
► Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
► The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool.
Accessories run-
ning faster than their rated speed can break
and fl y apart.
► The outside diameter and the thickness
of your accessory must be within the ca-
pacity rating of your power tool.
Incorrectly
sized accessories cannot be adequately
guarded or controlled.
► Threaded mounting of accessories must
match the grinder spindle thread. For ac-
cessories mounted by fl anges, the arbour
hole of the accessory must fi t the locating
diameter of the fl ange.
Accessories that do
not match the mounting hardware of the pow-
er tool will run out of balance, vibrate exces-
sively and may cause loss of control.
► Do not use a damaged accessory.
Before each use inspect the accessory
such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or
cracked wires. If power tool or accessory
is dropped, inspect for damage or in- stall
an undamaged accessory. After inspecting
and installing an accessory, position your-
self and bystanders away from the plane
of the rotating accessory and run the pow-
er tool at maximum no load speed for one
minute. Damaged accessories will normally
break apart during this test time.
► Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As ap-
propriate, wear dust mask, hearing protec-
tors, gloves and workshop apron capable
of stop- ping small abrasive or workpiece
fragments. The eye protection must be capa-
ble of stopping fl ying debris generated by var-
ious operations. The dust mask or respirator
must be capable of fi ltrating particles generat-
ed by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
►
Keep bystanders a safe distance away
from work area. Anyone entering the work
area must wear personal protective equip-
ment. Fragments of workpiece or of a broken
accessory may fl y away and cause injury be-
yond immediate area of operation.
► Hold the power tool by insulated grip-
ping surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool
"live" and could give the operator an electric
shock.
► Position the cord clear of the spinning
accessory.
If you lose control, the cord may
be cut or snagged and your hand or arm may
be pulled into the spinning accessory.
► Never lay the power tool down until the
accessory has come to a complete stop.