P.I.T. PMT20H-035A, Руководство пользователя

Страница: 6 / 24

Cordless multi-function tool
5
ing the charging process does not damage
the battery.
The lithium-ion battery is protected against
deep discharge by the “Electronic Cell Protec-
tion (ECP)”. When the battery is discharged,
the power tool is switched off by means of
a protective circuit: The application tool no
longer rotates.
To remove the battery, press the release but-
tons and pull the battery back and out of the
power tool.
Do not use force to do this.
Follow the instructions on correct disposal.
Changing the tool
► Wear protective gloves when changing
tools.
There is a risk of injury when touch-
ing the application tools.
Selecting an application tool
Please observe the application tools intended
for your power tool.
Fitting/changing the application tool
Remove the application tool if one has al-
ready been fitted. To remove the application
tool, use the hex key to loosen the clamping
bolt and remove the tool.
Position the required application tool (e.g.
plunge cut saw blade on the tool holder so
that the depressed centre is facing down-
wards (see fi gure on the graphics page, text
on the application tool should be legible from
above). Turn the application tool to a position
which is convenient for the job at hand and
allow it to lock into place in the cams
of the tool holder. Twelve positions off set by
30° are possible for this.
Secure the application tool using the bolt.
Tighten the bolt using the hex key until the
rounded head of the bolt is lying fl at against
the application tool.
► Check that the application tool is seat-
ed securely.
Application tools that are at-
tached incorrectly or are not securely fi xed
in place may come loose during operation,
thereby putting you at risk.
Selecting a sanding sheet
Different sanding sheets are available, de-
pending on the material you are working with
and the required surface removal rate:
Attaching/changing the sanding sheet on
the sanding plate
The sanding plate is fitted with a hook-and-
loop fastening, allowing sanding sheets with a
hook-and-loop backing to be secured quickly
and easily.
Tap the hook-and-loop fastening of the sand-
ing plate before fitting the sanding sheet to
facilitate maximum adhesion.
Position the sanding sheet so that it is flush
with one side of the sanding plate, then place
the sanding sheet on the sanding plate and
press it on fi rmly.
To ensure optimum dust extraction, make
sure that the punched holes in the sanding
sheet are aligned with the drilled holes in the
sanding plate.
To remove the sanding sheet, take hold of it
by a corner and pull it away from the sanding
plate.
Sanding accessories such as fl eece/polishing
felt are attached to the sanding plate in the
same way.
Dust/chip extraction
The dust from materials such as lead paint,
some types of wood, minerals and metal
can be harmful to human health. Touching or
breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the
user or in people in the near vicinity.
Certain dusts, such as oak or beech dust,
are classified as carcinogenic, especially in
conjunction with wood treatment additives
(chromate, wood preservative). Materials con-
taining asbestos may only be machined by
specialists.
– Use a dust extraction system that is suita-
ble for the ma- terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class
breathing mask.
The regulations on the material being ma-
chined that apply in the country of use must
be observed.
► Avoid dust accumulation at the work-
place.
Dust can easily ignite.
Operation
Starting Operation
Inserting the battery
► Use only original P.I.T. lithium-ion bat-
teries with the voltage stated on the
type plate of your power tool.
Using oth-
er batteries can lead to injuries and pose a
fi re hazard.
Note: The use of batteries unsuitable for your
power tool can lead to malfunctions or dam-
age to the power tool.
Insert the charged battery into the handle until
you feel it engage and it is fl ush with the han-
dle.
Switching on/off
► Make sure that you are able to press
the On/Off switch without releasing the
handle.