P.I.T. PDS20H-125A, Руководство по эксплуатации

Страница: 8 / 28

Cordless Random Orbital Sander
8
tape to prevent short circuit and energy
discharge. Do not attempt to open or re-
move any of the components.
Overload protection
► When overloaded, the motor comes to a
stop. Relieve the load on the tool immedi-
ately and release the on/off switch. Restart
the tool as no mal.
Temperature dependent oveload
protection
► When used as intended the power tool
cannot be subject to overload. When the
load is too high or the allowable battery
temperature is too hot, the electronic con-
trol switches off the power tool until the
temperature is in the optimumtemperature
range again.
Protection against deep discharg-
ing
► The li-ion battery is protected against deep
discharging by the “discharging protection
system”. When the battery is empty, the
tool is switched off by means of a protec-
tive circuit. The andom orbital sander will
no longer rotate.Remove the battery and
echarge.
Useful tips
► Your sander is ideal for working on wood,
metals and painted surfaces. It will smooth
surfaces prior to painting,even where fi llers
have been used and left proud.
► You sander is best suited to large fl at ar-
eas such as doors but can also be used
on skirting boards, windows,etc, provided
they are accessible.
► Diff erent types of sanding paper will allow
the sander to meet various needs. Diff er-
ent grades of sanding paper are available,
the higher grade number, the fi ne the grit.
For rough work start with a low grade of
grit [e.g. 60 Grit] and changer to a higher,
fi ner gader [e.g. 100 or 120] for fi nishing. If
you use a fi ner grade fo rough surfaces it
will soon clog and need changing.
► Let the sander do the work at all times. Do
not force it or apply excessive pressure
to the sanding paper or it could winkle or
tear .
► If the surface shows excessive markings
from the abrasive motion, you may be us-
ing a grit which is too coarse or applying
too much pressure.
from the dust extaction port and shake out
dust.
Dust extaction port
► A vacuum hose can be connected to the
dust extaction port for cleaner cutting
operations. The vacuum cleane must be
suitable for the material being worked on.
On/off switch (see fi g. D)
► To start your sander , depress the protec-
tive cover over the switch at the position
marked’’I”. To stop your sander , depress
the protective cover at the position marked
“O”.
Using the sander (see fi g. E)
► The workpiece to be sanded must be se-
cured.
► Be sure to hold the sander firmly while it
is on and apply it gently to the work, as it
may “kick”’on fi st contact. Hold the sander
so that it is fl at on the workpiece and move
in long,sweeping strokes across the sur-
face. Let the sander do the work. Applying
excessive pessure will slow the sander
and produce unsatisfactory results. Light
pressure is all that is needed for sanding,
polishing, or scrubbing. Regularly check
the condition of the sanding paper and re-
place it when worn for best results.
► Check you work often as this sander re-
moves material quickly. Do not allow your
sander to remain in the same position oth-
erwise, you will remove too much material
and create an uneven surface.
Disposal of an exhausted battery
pack
► Olympia tools provides a facility for the
collection and recycling of rechargeable li-
ion batteries once they have reached the
end of thei working life. To dispose of you
battery please return to any olympia tools
stockist who will collect them on our be-
half. Alternatively consult your local waste
authority for information regarding avail-
able recycling and/or disposal options. It
will then be ecycled or dismantled in orde
to reduce the impact on the environment
battery packs can be hazardous for the en-
vironment and to human health since they
contain hazardous substances.
► Discharge you battery pack by operating
your random orbital sander , then remove
the battery pack fom the andom orbital
sander housing and cove the battery pack
connections with heavy-duty adhesive