3
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Mounting the Cable Hook
1. Press the cable hook for the cable store
into the mount on the base of the unit.
2. After use, the power cable can
be conveniently wound onto the
cable hooks.
Fitting the Dust Bag
1. For vacuuming fine, dry dirt it is
recommended that you fit the dust
bag. The dust bag is suitable for dry
vacuuming only. Using the dust bag
makes it easier to dispose of the
dust that has been collected.
2. To attach, slip the dust bag over
the vacuum inlet.
NOTE:
Do not use the
dust bag
when
vacuuming liquid.
Fitting the Foam Filter -
Vacuuming Liquid
For wet-vacuuming, slip the supplied
foam filter over the filter basket.
NOTE:
Do not use the
filter bag and/or
dust bag
when vacuuming liquid
Fitting the Filter Bag -
Vacuuming Dry Matter
For dry vacuum cleaning always use the
filter bag. Mount the filter bag, so that
no air is sucked through the filter cage
without being filtered.
NOTE:
Do not use the
foam filter
when
vacuuming dry matter.
WET & DRY VACUUM
ACCESSORIES
KNOW YOUR PRODUCT
1. ASSEMBLY
3. FITTING HOSES & NOZZLES
2. FITTING THE FILTER
4. OPERATION
Connect the suction hose to the
corresponding connector on the
wet and dry vacuum, depending on
the application required:
Vacuuming
Connect the suction hose to
the vacuum inlet
Blowing
Connect the suction hose to
the blow outlet.
Extension Tube and Adaptor
1. The suction hose can be extended by attaching one or more sections
of the 3 part extension tubes.
2. The adapter must be inserted between
the extension tube and whichever of the
nozzles is required.
Suction Tools
Floor Tool
The floor tool is for vacuuming solids and liquids
over medium to large areas.
Crevice Tool
The crevice tool is designed for cleaning crevices
and edges.
SETUP & PREPARATION
OPERATION
IMPORTANT!
SWITCH OFF THE EQUIPMENT IF LIQUID
OR FOAM IS EMITTED WITH THE EXHAUST AIR WHEN
WET VACUUM CLEANING.
IMPORTANT!
WHEN WET VACUUMING, THE SAFETY
FLOAT TURNS OFF THE WET AND DRY VACUUM
CLEANER AUTOMATICALLY WHEN THE MAXIMUM
LEVEL IS REACHED.
IMPORTANT!
THE WET AND DRY VACUUM CLEANER
IS NOT SUITABLE FOR THE VACUUMING OF
COMBUSTIBLE LIQUIDS.
IMPORTANT!
NEVER USE THE WET AND DRY VACUUM
CLEANER WITHOUT A FILTER! ALWAYS ENSURE THAT
THE FILTERS ARE PERFECTLY SECURE!
Assembling the Castors
1. Turn the container upside down.
2. Insert the castor assemblies into
the base of the tank. Use firm hand
pressure. Use of a hammer may damage
the castor.
Fitting the Motor
1. When fitting the motor to the tank,
position it so that the motor securing
clips on the tank align with the
fastening points on the motor.
2. Fasten the motor securing clips to the
motor, making sure that they
lock into place correctly.
3. To remove the motor, open the
motor securing clip and lift the motor out
of the tank.
Fitting the Handle
1. Align the holes on either side of the
handle with the holes in the top side
of the motor.
2. Insert two screws (supplied) into the
handle and tighten with a screwdriver (not
supplied).
VWD-1220PTU
On/Off Switch
Switch position 0: OFF
Switch position I: Normal operation
Switch position II: Automatic mode
Dry Vacuuming
Use the dust bag and the filter bag for dry
vacuuming (see
2. Fitting the Filter
).
Check that the filter is securely fitted at all
times.
Wet Vacuuming
For wet-vacuuming, use the foam filter
(see
2. Fitting the Filter
).
Check that the filter is securely fitted
at all times.
NOTE:
The tank will collect 12 Litre max of
fluid and the float switch will turn off the vac.
Blowing
Connect the suction hose to the blow outlet
on the wet and dry vacuum cleaner.
1. Handle
2. Motor
3. Suction Hose
4. Filter Basket
5. Safety Float
6. Extension Tubes
7. Blow Outlet
8. Motor Securing Clips
9. Tank
10. Cable Hook
11. Adapter
12. On/Off/Auto Switch
13. Auto Power-Outlet
14. Vacuum Inlet
15. Castors
16. Floor Tool
17. Filter Bag
18. Dust Bag
19. Foam Filter
20. Crevice Tool
21. Electric Tool Adaptor
22. Handle Screws
1
2
3
4
5
6
7
8
9
10
11
13 14
16
17
18
19
20
15
12
22
21
