![background image](http://html1.mh-extra.com/html/ozito/scms-8multi/scms-8multi_instruction-manual_1666652007.webp)
WARNING!
ENSURE THAT THE CORRECT BLADE
BUSH THAT MAY BE REQUIRED SUITS THE
SPINDLE & BLADES THAT ARE FITTED,
WARNING!
TO ENSURE THE CORRECT BLADE
ROTATION, ALWAYS INSTALL THE BLADE WITH
THE TEETH POINTING DOWNWARDS. ENSURE
THE ARROW DIRECTION ON THE BLADE
CORRESPONDS WITH THE ARROW ON THE UPPER
BLADE GUARD.
Carbon Brushes
When the carbon brushes wear out, the mitre saw will spark
and/or stop. Discontinue use as soon as this happens. They
should be replaced prior to recommencing use of the mitre
saw. Carbon brushes are a wearing component of the mitre
saw therefore not covered under warranty. Continuing to use
the mitre saw when carbon brushes need to be replaced
may cause permanent damage to the mitre saw. Carbon
brushes will wear out after many uses but when the carbon brushes need to be
replaced, take the mitre saw to an electrician or a power tool repairer for a quick
and low cost replacement. Always replace both carbon brushes at the same
time.
Note:
Ozito Industries will not be responsible for any damage or injuries caused
by the repair of the mitre saw by an unauthorised person or by mishandling of
the mitre saw.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents. This is
normal and does not indicate a problem.
Fence Alignment
The fence holds the workpiece in a fixed position while the table and or the
blade assembly are adjusted in a mitre or bevel angle. To make accurate cuts,
the Fence must be perpendicular (at a 90° angle) to the saw blade.
1. Before beginning work, make a test cut on a scrap material with the table
set at 90°.
2. Check the cut with an accurate square. You can also reverse the two pieces,
hold the cut ends together, and hold a good straight edge along the side of
the pieces
3. If either test reveals that the cut is not a true 90° angle, adjust the fence
before beginning work.
If Fence Needs Adjustment:
1. First unplug the tool
2. Lower the blade assembly and lock it in place using the Lock Down Pin.
3. Lay a carpenters’ square on the turn table one edge along the blade and the
other along the fence. Any inaccuracy should be visible. Note: The square
must contact the blade, not the teeth, for an accurate reading.
4. The fence is held in place with bolts at each end. Loosen the bolts slightly
and, gently tap the fence into position using a soft mallet. Retighten the bolts
and make another test cut. Repeat the process until the fence is adjusted
accurately.
5. Once the fence is accurately adjusted, tighten the bolts firmly in place.
Recheck one last time, then proceed to work.
Transportation
The lock down pin is provided for holding the cutting head down whilst
transporting or storing the mitre saw. The saw must never be used with the lock
down pin locking the head down. Tighten the slide lock during transportation
Power tools that are no longer usable should not be
disposed of with household waste but in an environmentally
friendly way. Please recycle where facilities exist. Check
with your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in
the environment. Please recycle packaging where facilities
exist. Check with your local council authority for recycling
advice.
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
SPARE PARTS
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
Revolutions or
reciprocation per minute
n
o
No load speed
Warning
Wear hearing protection
Read instruction manual
Wear eye protection
Wear eye, ear & breathing
protection
Double insulated
/min
Keep hands away from blade
R.C.M. Regulatory
compliance mark
Wear gloves
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]