background image

battery Charge Indicator

The purchased battery is equipped 

with a battery charge indicator to 

show the state of the battery charge.
Press the charge indicator button and 

look to see which LED lights.

Battery requires 

immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note:

 The battery needs to be removed from the tool to check the state 

of charge. 

1    Connect the charger into a mains power outlet.

4  The charger LED will illuminate red signifying that the battery 

is charging.

3   With the battery sitting on a flat 

surface, align the raised ribs 

on the battery with the recess 

in the charger and slide onto 

the battery ensuring a firm 

connection.

2   The charger LED will flash 

green showing power 

is being supplied to the 

charger.

5  When removing the charger 

from the battery, first press the 

battery release tab, then slide 

the charger from its position.

Charging your lithium ion battery - Eco Charger

Charger LED Indicator 

LED Indicator 

Situation

GREEN (Flashing) 

Stand By (no battery pack is inserted) 

RED (Illuminated)

Battery is charging (low charge)

GREEN (Illuminated)

Battery is fully charged

RED (Flashing)

Battery or Charger fault

RED & GREEN 

(Flashing)

Battery pack is too hot or too cold (remove 

battery from charger and store at room 

temperature 20ºC. Insert battery again when 

at correct charging temperature). If this 

happens again, the battery is defective and 

needs to be replaced.

2.  BATTERY & CHARGING 

(sold separately)

The purchased battery will be shipped in a low charge condition, and 

requires charging prior to use. Allow several cycles of charging and 

discharging (through use of the tool) for the battery to reach its optimum 

performance / runtime.

CAUtION:

 

thE ChARGER FOR thIS pRODUCt ShOULD 

bE pROtECtED by A RESIDUAL CURRENt DEvICE 

(RAtED At 30MA OR LESS).

1    Connect the charger into a mains power outlet.

4  The charger LED will 

illuminate red signifying that 

the battery is charging.

3   With the charger sitting on a 

flat surface, align the raised 

ribs on the battery with 

the recess in the charger 

and slide onto the charger 

ensuring a firm connection.

2   The charger LED will flash 

green showing power 

is being supplied to the 

charger.

5  The charger LED will 

illuminate green once the 

battery is fully charged.

Charging your lithium ion battery - Fast Charger

Charger LED Indicator 

LED Indicator 

Situation

GREEN (Flashing) 

Stand By (no battery pack is inserted) 

RED (Flashing)

Battery is charging (low charge)

RED (Illuminated)

Battery is charging (mid charge)

GREEN (Illuminated)

Battery is fully charged

BOTH(Illuminated)

Battery pack is too hot or too cold (charging 

will begin automatically when battery reaches 

correct charging temperature).

BOTH (Flashing)

Defective battery. Never charge a defective 

battery pack!
Remove battery pack from charger.

Содержание PXMSS-700










Отзывы: