DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
TROUBLESHOOTING
CONNECTION WITH TANK BASE BELOW WATER PUMP
P
CONNECTION WITH TANK BASE ABOVE THE WATER PUMP
CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP
0
1
2
3
4
5
6
Bar
FIRM BASE
SOLID STRUCTURE
0
1
2
3
4
5
6
Bar
WATERTANK
WATERTANK
NON-RETURN
VALVE
DISCHARGE
OUTLET
GATE
VALVE
GATE
VALVE
SUCTION LINE
SUCTION LINE
150mm
150mm
150mm
150mm
150mm
FIRM BASE
SOLID STRUCTURE
0
1
2
3
4
5
6
Bar
DISCHARGE
OUTLET
150mm
UNION
COUPLING
depending on
installation
UNION
COUPLING
depending on
installation
WATERTANK
GATE
VALVE
SUCTION LINE
SOLID STRUCTURE
DISCHARGE
OUTLET
FIRM BASE
UNION
COUPLING
depending on
installation
IN-LINE
FILTER
IN-LINE
FILTER
IN-LINE
FILTER
Problem
LED Display
Possible Cause
Solution
The pump operates
but water is not
flowing
Yellow, green and red
LEDs are on
There is air in the pump head
Disconnect from power supply, open the priming screw and fill the
pump head with water
Verify the joints are sealed tightly with Teflon tape
The suction pipe is blocked
Disconnect from power supply, clean the suction pipe
The pump is not primed
Following instructions “Priming The Pump”
The in-line filter is blocked
Clean the filter
The inlet and outlet are not
connected with the pipe or hose
correctly
Connect the inlet and outlet with pipe or hose correctly, ensure
there is no leakage. Use Teflon tape on all connections.
No water flow from supply
Check if the supply source has sufficient water
The pump won’t start No LEDs on
Power not switched on
If the yellow light doesn’t illuminate, check the mains supply
Yellow LED on
On button has not been pressed
Once connected with the mains power, the yellow light will
illuminate. When this occurs, press the On button.
Pumps stops
No LEDs on
The mains power is disconnected Check the mains power
Power failure
When power is restored, the yellow light will illuminate, press the
On button
Yellow and red LEDs
are on
There is air in the pump head
Disconnect from power supply, open the priming screw and fill the
pump head with water
Verify all joints are sealed tightly with Teflon tape
The suction pipe is blocked
Disconnect from power supply, clean the suction pipe
The pump is not primed
Follow instructions “Priming The Pump”
The external in-line filter is
blocked
Clean the external filter
The inlet and outlet are not
connected with the pipe or hose
correctly
Connect the inlet and outlet with pipe or hose correctly, ensure
there is no leakage. Use Teflon tape on all connections
No water flow from supply
Check if the tank has plenty of water
Yellow LED flashing
System has reached cut off
pressure of 3.8 bar
This is normal operation. The pump will start automatically once
the outlet system pressure is below 1.5 bar. Open outlet.
Pump cannot be
started by pressing
On button
Yellow LED on and
red LED flashing
Pump has gone to self protection
mode due to frequent on/off cycle
Check if there are any leaks in the outlet system. Fix any leaks
found. Ensure Teflon tape is used on all connections. Pump must
be disconnected from mains power to reset.
