• Keep the vents of the sander clean at all times. If possible, prevent foreign
matter from entering the vents.
• After each use, blow air through the sander housing to ensure it is free from
all dust particles which may build up. Build up of dust particles may cause the
sander to overheat and fail.
• If the enclosure of the sander requires cleaning, do not use solvents but a
moist soft cloth only. Never let any liquid get inside the sander; never immerse
any part of the sander into a liquid.
Carbon Brushes
When the carbon brushes wear out, the sander
will spark and/or stop. Discontinue use as soon
as this happens. They should be replaced prior to
recommencing use of the sander. Carbon brushes
are a wearing component of the sander and are
therefore not covered under warranty. Continuing
to use the sander when carbon brushes need to
be replaced may cause permanent damage to the
sander. Carbon brushes will wear out after many uses. When the carbon
brushes need to be replaced, take the sander to an electrician or a power tool
repairer for a quick and low cost replacement. Always replace both carbon
brushes at the same time.
Note: Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the sander by an unauthorised person or by
mishandling of the sander.
MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLE SHOOTING
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Dust extraction system is not working
The dust extraction system is powered by an internal fan attached to the tools
motor, therefore will only function while the tool is in operation. Higher speed
provides better extraction.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Excessive sparking visible through the housing air vents
and/or the drill failing to operate
May indicate the carbon brushes have worn out and need to be replaced. Carbon
brushes should only be replaced by a qualified electrician or power tool repairer.
Sandpaper Selection
Selecting the correct grit of sandpaper is an important step in achieving optimum
results. Coarse grit will remove the most material. Finer grit will produce a
smoother finish. The condition of the work piece will determine the grit of
the sandpaper to be used. The higher the grit number, the finer the grade of
sandpaper.
If the surface is rough, start with a coarse grit and sand until the surface is
uniform. Medium grit may then be used to remove scratches left by the coarser
grit. Finer grit is then used to finish the surface. Always continue sanding with
each grade of sandpaper until the surface is uniform.
Note
: If intermediate sanding is required, choose a grit rating between coarse and
fine. The above table is intended as a guide only. To ensure a satisfactory result,
a small, inconspicuous area should first be tested to ensure the grit of sandpaper
chosen is suitable for the desired finish.
Sanding Tips
Never force the sander. The weight of the sander supplies adequate pressure,
allowing the sandpaper to do the work. Applying additional pressure will slow the
motor, rapidly wear the sandpaper, and greatly reduce the sander speed. This will
slow the removal rate and produce an inferior quality surface.
CAUTION
: Excessive pressure will overload the motor, causing possible damage
to the sander by overheating the motor; or damage to the work piece.
Be sure to check your work piece often. The sander is capable of removing
material rapidly, especially with coarse paper.
The orbital action of your sander allows you to sand with the grain, or at any angle
across it for most sanding jobs. In the final stages a better finish will be achieved
by sanding with the grain.
Do not sand on one spot for too long. The sander’s rapid action may remove too
much material, creating an uneven surface.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
Warning
Read instruction manual
Wear eye protection
Double insulated
min
-1
Revolutions or
reciprocation per minute
n
0
No load speed
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
Diameter
Regulator compliance mark
Wear ear protection
mm
Millimetres